Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001GXJY
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 09/2022]
Title: LIGHTING (INT): LIGHTING SYSTEM (for HV Model): Power Switch Illumination Circuit; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]

Power Switch Illumination Circuit

DESCRIPTION

The illuminated entry system controls the power switch illumination.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Smart Key > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Power/Engine SW Light

Power switch illumination

OFF or ON

-

Body Electrical > Smart Key > Active Test

Tester Display

Power/Engine SW Light

OK:

Power switch illumination comes on.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; LIGHTING (INT): LIGHTING SYSTEM (for HV Model): PROBLEM SYMPTOMS TABLE 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; LIGHTING (INT): LIGHTING SYSTEM (for HV Model): PROBLEM SYMPTOMS TABLE

NG

2.

INSPECT POWER SWITCH

(a) Remove the power switch.

Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (STARTING): POWER SWITCH: REMOVAL

(b) Inspect the power switch.

Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (STARTING): POWER SWITCH: INSPECTION

NG

REPLACE POWER SWITCH

OK

3.

CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the I1 certification ECU (smart key ECU assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I119-5 (SWIL) - I1-10 (SWIL)

Always

Below 1 Ω

I119-3 (GND) - I1-11 (AGND)

Always

Below 1 Ω

I119-5 (SWIL) or I1-10 (SWIL) - Body ground

Always

10 kΩ or higher

I119-3 (GND) or I1-11 (AGND) - Body ground

Always

10 kΩ or higher
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR