Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001GXJ0 |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: LIGHTING (INT): LIGHTING SYSTEM (for Gasoline Model): IG Signal Circuit; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2022] |
DESCRIPTION
This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
IG SW
|
Ignition switch ON signal
|
OFF or ON
|
OFF: Ignition switch off
ON: Ignition switch ON
|
"OFF" is also displayed for this item when the ignition switch is ACC.
|
Body Electrical > Main Body > Data List
OK:
Normal conditions listed above are displayed.
NG
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)
|
(a) Disconnect the 4D and 4F instrument panel junction block assembly connectors.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
4D-1 - Body ground
|
Always
|
11 to 14 V
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
4F-3 - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - BODY GROUND)
|
(a) Disconnect the I86 main body ECU (multiplex network body ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I86-19 (GND2) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (IG1-NO. 1 RELAY POWER SOURCE)
|
*a
|
Component with harness connected
(Instrument Panel Junction Block Assembly)
|
-
|
-
|
(a) Connect the 4D and 4F instrument panel junction block assembly connectors.
(b) Connect the I86 main body ECU (multiplex network body ECU) connector.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
4E-17 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
*a
|
Component without harness connected
(Instrument Panel Junction Block Assembly)
|
-
|
-
|
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
4F-3 - MB-11 (GND1)
|
Always
|
Below 1 Ω
|
4D-1 - MB-32 (IG)
|
Battery not connected to 4E-17 and 4F-3
|
10 kΩ or higher
|
4D-1 - MB-32 (IG)
|
Battery positive (+) → 4E-17
Battery negative (-) → 4F-3
|
Below 1 Ω
|
|