SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001GX8L
Model Year Start: 2020	Model: GR Corolla	Prod Date Range: [01/2019 - 03/2019]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side No. 1 airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Pre-collision System

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*1: for Hatchback
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock*1	Power Door Lock Control System

NOTICE:

for HV Model:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

for Gasoline Model:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for HV Model: Click here

for Gasoline Model: Click here

NOTICE:

After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS: Click here

for 2ZR-FAE: Click here

for 2ZR-FXE: Click here

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY (for Gasoline Model)

Click here

4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Click here

5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Click here

6. REMOVE FRONT DOOR SCUFF PLATE

for Hatchback: Click here

for Sedan: Click here

7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.

8. REMOVE REAR DOOR SCUFF PLATE

for Hatchback: Click here

for Sedan (for HV Model): Click here

for Sedan (for Gasoline Model): Click here

9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.

10. REMOVE CENTER PILLAR LOWER GARNISH

for Hatchback: Click here

for Sedan: Click here

11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.

*a	Protective Tape
*b	Locking Button
*c	Release

(b) Remove the 2 bolts.

12. REMOVE SIDE NO. 1 AIRBAG SENSOR

(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a	White Housing Lock	*b	Yellow CPA
*c	Connector lock is released	-	-

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(d) Remove the nut and disengage the claw to remove the side No. 1 airbag sensor.

(e) Check that the position of the white housing lock is as shown in the illustration.

Incorrect

Correct