HEATING / AIR CONDITIONING: COMPRESSOR (for 2ZR-FXE): INSTALLATION; 2020 - 2022 MY Corolla Corolla HV [01/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001GW8A
Model Year Start: 2020	Model: Corolla	Prod Date Range: [01/2019 - 09/2022]
Title: HEATING / AIR CONDITIONING: COMPRESSOR (for 2ZR-FXE): INSTALLATION; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]

INSTALLATION

PROCEDURE

1. ADJUST COMPRESSOR OIL

(a) When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 110 to 125 cc (3.73 to 4.22 fl. oz)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor)

NOTICE:

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.
If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.
Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.

2. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

(a) Install the compressor with motor assembly with the 3 bolts.

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

HINT:

Tighten the bolts in the order shown in the illustration.

(b) Install the bracket with the bolt.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

*a	Connector (A)
*b	Connector (B)
*c	Green-colored Lock
	Slide

(d) Remove the insulating tape from the connector (A).

(e) Connect the connector (A) and slide the green-colored lock as shown in the illustration to securely lock it.

CAUTION:

Make sure to wear insulated gloves.

NOTICE:

Make sure that the connector is connected securely.

3. CONNECT SUCTION HOSE SUB-ASSEMBLY

(a) Remove the vinyl tape from the suction hose sub-assembly.

(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(d) Connect the suction hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

4. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

(a) Remove the vinyl tape from the discharge hose sub-assembly.

(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(d) Connect the discharge hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

5. INSTALL INLET NO. 1 AIR CLEANER

Click here

6. INSTALL AIR CLEANER BRACKET

Click here

7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here

8. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Click here

10. INSTALL AIR CLEANER HOSE ASSEMBLY

Click here

11. INSTALL INLET NO. 2 AIR CLEANER

Click here

12. INSTALL RADIATOR SUPPORT OPENING COVER

Click here

13. INSTALL SERVICE PLUG GRIP

Click here

14. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

Click here

15. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))

Click here

16. WARM UP COMPRESSOR (for HFC-134a(R134a))

Click here

17. WARM UP COMPRESSOR (for HFO-1234yf(R1234yf))

Click here

18. INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))

Click here

19. INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))

Click here