Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GW2B
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 -           ]
Title: WIPER / WASHER: WIPER AND WASHER SYSTEM (for Gasoline Model): DATA LIST / ACTIVE TEST; 2020 - 2025 MY Corolla Corolla Hatchback GR Corolla [01/2019 -        ]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus:

(1) for Main Body: Body Electrical / Main Body / Data List.

(2) for Combination Meter: Body Electrical / Combination Meter / Data List.

(3) for Steering Angle Sensor: Chassis / Steering Angle Sensor / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication Humidity/Rain Sensor

Connection status between rain sensor and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTCs are stored if a malfunction occurs in the CAN communication system.

The Number of DTC

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Washer Level Warning Switch

Washer fluid level warning switch

OFF or ON

OFF: Washer fluid level not low

ON: Washer fluid level low

-

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Wiper OFF Switch

Front wiper switch OFF position signal

OFF or ON

OFF: Front wiper switch not in OFF position

ON: Front wiper switch in OFF position

-

Wiper Auto/Int Switch

Front wiper switch INT position signal

OFF or ON

OFF: Front wiper switch not in INT position

ON: Front wiper switch in INT position

-

Wiper Lo Switch

Front wiper switch LO position signal

OFF or ON

OFF: Front wiper switch not in LO position

ON: Front wiper switch in LO position

-

Wiper Hi Switch

Front wiper switch HI position signal

OFF or ON

OFF: Front wiper switch not in HI position

ON: Front wiper switch in HI position

-

Wiper Mist Switch

Front wiper switch MIST position signal

OFF or ON

OFF: Front wiper switch not in MIST position

ON: Front wiper switch in MIST position

-

Washer Switch

Washer switch Fr WASH position signal

OFF or ON

OFF: Washer switch not in Fr WASH position

ON: Washer switch in Fr WASH position

-

Rear Wiper Lo Switch

Rear wiper switch Rr ON position signal

OFF or ON

OFF: Rear wiper switch not in Rr ON position

ON: Rear wiper switch in Rr ON position

*1

Rear Wiper Hi Switch

Rear wiper switch Rr INT position signal

OFF or ON

OFF: Rear wiper switch not in Rr INT position

ON: Rear wiper switch in Rr INT position

*1

Rear Washer Switch

Washer switch Rr WASH position signal

OFF or ON

OFF: Washer switch not in Rr WASH position

ON: Washer switch in Rr WASH position

*1

Intermittent Time Volume

Intermittent time adjustment switch condition

Shortest, Shorter, Longer or Longest

Shortest: P4

Shorter: P3

Longer: P2

Longest: P1

*2

Wiper Spec Info

Function information

Unknown, Auto spec or INT spec

Unknown: Specification not stored

Auto spec: w/ Auto wiper system

INT spec: w/o Auto wiper system

-

The Number of DTCs

Number of trouble codes

0 to 255

Number of stored DTCs displayed

-

  • *1: w/ Rear Wiper System
  • *2: Refer to Inspection for each position of the switch. (w/ Intermittent Time Adjustment Switch)

    Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; WIPER / WASHER: WIPER SWITCH: INSPECTION

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Wiper Power Relay

Function to operate the IG1 NO. 3 relay

OFF or ON

-

Front Washer Relay

Function to operate the windshield washer motor and pump assembly (Front)

OFF or ON

-

Rear Washer Relay

Function to operate the windshield washer motor and pump assembly (Rear)

OFF or ON

*

Rear Wiper Operation

Function to operate the rear wiper motor assembly

OFF or ON

*

Front Wiper Lo Operation

Function to operate the windshield wiper motor assembly in LO

OFF or ON

-

Front Wiper Hi Operation

Function to operate the windshield wiper motor assembly in HI

OFF or ON

-

  • *: w/ Rear Wiper System