| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001GS12 |
| Model Year Start: 2020 | Model: Corolla Hatchback | Prod Date Range: [01/2019 - 09/2022] |
| Title: M20A-FKS (FUEL): FUEL PUMP (w/ Canister Pump Module (for Double Wishbone Type Suspension)): INSTALLATION; 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022] | ||
INSTALLATION
PROCEDURE
1. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(a) Install a new fuel suction tube set gasket to the fuel tank assembly.
(b) Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.
NOTICE:
- Be careful not to bend the arm of the fuel sender gauge assembly.
- Make sure the horizontal angle of the fuel suction plate sub-assembly is less than 90°.
- To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.
|
*1 |
Fuel Sender Gauge Assembly |
*2 |
Fuel Sub-tank Sub-assembly |
|
*3 |
Fuel Suction Plate Sub-assembly |
- |
- |
|
*a |
90° |
- |
- |
|
*a |
Protrusion |
|
*b |
Notch |
(c) Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.
|
*a |
Protrusion |
|
Notch |
2. INSTALL FUEL PUMP GAUGE RETAINER
(a) Install the fuel pump gauge retainer.
(1) While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.
|
(2) Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer. SST: 09808-01071 SST: 09808-14031 09808-01030 09808-01090 HINT: Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer. |
|
(3) While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
(4) Install SST (handle) and an extension bar (270 mm) to SST (plate).
|
*a |
Triangle Mark (Fuel Pump Gauge Retainer) |
|
*b |
Triangle Mark (Fuel Tank Assembly) |
|
*c |
SST (Handle) |
|
*d |
SST (Plate) |
|
*e |
SST (Claw) |
|
*f |
SST (Bolt) |
|
*g |
Extension Bar (270 mm) |
|
|
Tighten |
|
Front Side |
SST: 09808-01071
SST: 09808-14031
09808-01010
09808-01030
09808-01090
(5) Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.
NOTICE:
- Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
- Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
- Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
- Do not spin SST too fast or use an impact wrench as this may result in damage to components.
- If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
- Make sure that the fuel suction tube set gasket does not come off.
3. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.
|
*1 |
Fuel Suction Plate Sub-assembly |
*2 |
Tube Joint Clip |
|
*3 |
Fuel Tank Main Tube Sub-assembly |
- |
- |
|
*a |
Fuel Tube Joint |
*b |
O-ring |
|
*c |
Correct |
*d |
Incorrect |
|
*e |
Collar |
- |
- |
|
|
Insert |
|
Insert |
NOTICE:
- Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
- Check that the fuel tube joint is securely inserted to the end.
- Check that the tube joint clip is on the collar of the fuel tube joint.
- After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.
(b) Engage the 2 claws to install the No. 1 fuel tube clamp.
4. CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY
(a) Connect the fuel tank vent hose sub-assembly to the fuel suction tube with pump and gauge assembly.
Click here
![2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (FUEL): FUEL SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
5. INSTALL REAR FLOOR SERVICE HOLE COVER
(a) Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.
(b) Clean the installation surfaces of the rear floor service hole cover and vehicle body.
(c) Connect the 2 fuel suction tube with pump and gauge assembly connectors.
(d) Install the rear floor service hole cover with new butyl tape.
6. INSTALL NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Hatchback)
Click here
7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here
8. INSPECT FOR FUEL LEAK
Click here
9. INSTALL REAR SEAT ASSEMBLY
Click here
10. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing the fuel pump.
Click here
|
|