Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001GOOL |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [01/2019 - 03/2019] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR (for Gasoline Model): REMOVAL; 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 03/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System (for Hatchback)
|
|
Replacement of brake actuator assembly
|
Perform acceleration sensor zero point calibration and store system information memorization
|
-
VSC is disabled or malfunctions
-
DTCs are output
-
Slip indicator light illuminates
-
ABS warning light illuminates
|
w/ Electric Parking Brake System:
w/o Electric Parking Brake System:
|
Operate the electric parking brake switch (electric parking brake switch assembly)
|
Parking brake indicator light (red) blinks when the ignition switch is first turned on (IG)
|
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
3. DRAIN BRAKE FLUID
NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.
4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here
5. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
Click here
6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
Click here
7. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for M20A-FKS)
Click here
8. REMOVE DASH PANEL HEAT INSULATOR (for M20A-FKS)
(b) Remove the 2 nuts and dash panel heat insulator.
|
|
9. REMOVE BRAKE ACTUATOR WITH BRACKET
(a) Release the lock lever and disconnect the connector from the brake actuator assembly.
|
Release the lock lever
|
|
Disconnect the connector
|
NOTICE:
Be careful not to allow any brake fluid to enter the connector.
(b) Use tags or make a memo to identify the places to reconnect the brake lines.
|
|
*a
|
From 1st Chamber of Brake Master Cylinder Sub-assembly
|
*b
|
From 2nd Chamber of Brake Master Cylinder Sub-assembly
|
*c
|
To Front Wheel Cylinder Assembly RH
|
*d
|
To Rear Wheel Cylinder Assembly LH
|
*e
|
To Rear Wheel Cylinder Assembly RH
|
*f
|
To Front Wheel Cylinder Assembly LH
|
|
|
(c) Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.
NOTICE:
-
Do not kink or damage the brake lines.
-
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
|
|
(d) Disengage the 5 clamps to remove the No. 1 brake tube clamp from the brake lines.
NOTICE:
Do not kink or damage the brake lines.
|
|
(f) Remove the bolt and brake actuator with bracket.
NOTICE:
-
Do not kink or damage the brake lines.
-
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
-
Be careful not to allow any brake fluid to enter the connector.
-
Do not hold the brake actuator assembly by the connector.
-
Do not drop the brake actuator with bracket when carrying it.
HINT:
Remove the brake actuator with bracket while avoiding the brake lines.
|
|
10. REMOVE BRAKE ACTUATOR ASSEMBLY
(a) Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.
NOTICE:
-
Do not hold the brake actuator assembly by the connector.
-
Be careful not to allow any brake fluid to enter the connector.
-
Do not drop the brake actuator assembly when carrying it.
|
|
11. REMOVE BRAKE ACTUATOR BRACKET CUSHION
(a) Remove the 3 nuts and separate the brake actuator bracket assembly.
|
|
*1
|
No. 1 Brake Actuator Case Collar
|
*2
|
Brake Actuator Bracket Cushion
|
*3
|
Brake Actuator Bracket Assembly
|
|
|
(b) Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.
(c) Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.
|