2ZR-FXE (FUEL): FUEL INJECTOR: REMOVAL; 2020 MY Corolla Corolla HV [01/2019

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001GNKE
Model Year Start: 2020	Model: Corolla	Prod Date Range: [01/2019 - 04/2020]
Title: 2ZR-FXE (FUEL): FUEL INJECTOR: REMOVAL; 2020 MY Corolla Corolla HV [01/2019 - 04/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Control System (for HV Model)
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Pre-collision System (for HV Model)
Replacement of fuel injector assembly Replacement of EGR valve assembly Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.
Replacement of inverter with converter assembly	Resolver learning	DTCs are stored Slight vibration at a vehicle speed of 5 km/h (3 mph) or less Shock or vibration during acceleration
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on

CAUTION:

Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

PROCEDURE

1. DISCHARGE FUEL SYSTEM PRESSURE

Click here

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

3. REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY

Click here

4. DISCONNECT NO. 2 VENTILATION HOSE

(a) Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.

5. DISCONNECT ENGINE WIRE

(a) Disconnect the 4 fuel injector assembly connectors.

(b) Remove the bolt.

6. DISCONNECT FUEL TUBE SUB-ASSEMBLY

(a) Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.

	Open
	Pull

(b) Disconnect the fuel tube sub-assembly from the fuel pipe.

Click here

7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

(a) Remove the bolt to separate the clamp of the fuel delivery pipe sub-assembly from the cylinder head sub-assembly.

(b) Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 fuel injector assemblies.

NOTICE:

If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

8. REMOVE NO. 1 DELIVERY PIPE SPACER

(a) Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.

9. REMOVE FUEL INJECTOR ASSEMBLY

(a) Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

(b) Remove the O-ring from each fuel injector assembly.

(c) Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.

(d) Remove the 4 injector vibration insulators from the cylinder head sub-assembly.