EC65 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE: ADJUSTMENT; 2020 MY Corolla Corolla Hatchback [01/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001GN1S
Model Year Start: 2020	Model: Corolla Hatchback	Prod Date Range: [01/2019 - 03/2019]
Title: EC65 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE: ADJUSTMENT; 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]

ADJUSTMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly adjustment are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*1: w/o Smart Key System
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System (for Gasoline Model)
		Pre-collision System (for Gasoline Model)
		Lighting System (w/ AFS)(EXT)
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
Replacement of ECM	ECU communication ID registration (Immobiliser system)	Engine start function
Replacement of ECM*1	Code registration (Immobiliser system)	Engine start

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

4. REMOVE BATTERY

Click here

5. REMOVE CONSOLE BOX ASSEMBLY

Click here

6. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here

7. REMOVE RADIATOR SUPPORT OPENING COVER

Click here

8. REMOVE INLET NO. 1 AIR CLEANER

Click here

9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Click here

11. REMOVE ECM

Click here

12. DISCONNECT ENGINE WIRE

Click here

13. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

14. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:

After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.
If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.

(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.

(b) Push the 2 claws together at the top of the lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to push up the lock piece.

*a	Lock Piece	*b	Bottom View
*c	Push	*d	Push up

NOTICE:

Securely install the end of the floor shift transmission control select cable to the transmission floor shift assembly.
Install the end of the floor shift transmission control select cable so that its adjustment lock section is on the driver side.

(d) Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.

*1	Outer Select Lever
*2	Reverse Restrict Pin Assembly
*a	Secured

(e) Push the slider shaft against the cam wall.

NOTICE:

Do not pull up the slider shaft.
When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

*a	Slider Shaft
*b	Cam Wall

(f) Push the lock piece into the adjuster case.

NOTICE:

Securely push in the lock piece until the 2 claws are engaged.
When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

*a	Lock Piece
*b	Adjuster Case
*c	Push in

(g) Move the shift lever to the reverse position, so that the outer select lever can be released.

*1	Outer Select Lever
*2	Reverse Restrict Pin Assembly
*a	Released

15. INSTALL BATTERY CLAMP SUB-ASSEMBLY

Click here

16. CONNECT ENGINE WIRE

Click here

17. INSTALL ECM

Click here

18. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here

19. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

20. INSTALL INLET NO. 1 AIR CLEANER

Click here

21. INSTALL RADIATOR SUPPORT OPENING COVER

Click here

22. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here

23. INSTALL CONSOLE BOX ASSEMBLY

Click here

24. INSTALL BATTERY

Click here

25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here