2ZR-FXE (ENGINE MECHANICAL): CYLINDER HEAD GASKET: INSTALLATION; 2020 - 2025 MY Corolla Corolla HV [01/2019

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001GMHM
Model Year Start: 2020	Model: Corolla	Prod Date Range: [01/2019 - ]
Title: 2ZR-FXE (ENGINE MECHANICAL): CYLINDER HEAD GASKET: INSTALLATION; 2020 - 2025 MY Corolla Corolla HV [01/2019 - ]

INSTALLATION

PROCEDURE

1. INSTALL CYLINDER HEAD GASKET

(a) Remove any oil from the contact surfaces.

(b) Apply seal packing to the cylinder block sub-assembly as shown in the illustration.

*a	Cylinder Block Sub-assembly
*b	3.0 to 5.0 mm (0.118 to 0.197 in.)
*c	10 to 15 mm (0.394 to 0.591 in.)
*d	Diameter 7.0 to 9.0 mm (0.276 to 0.354 in.)
	Front of Engine

NOTICE:

Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes of applying seal packing.

*a	Lot No.
	Front of Engine

NOTICE:

Make sure to install the cylinder head gasket in the correct direction.

(d) Apply seal packing to the cylinder head gasket as shown in the illustration.

*a	Cylinder Head Gasket
*b	Diameter 6 to 8 mm (0.236 to 0.315 in.)
	Front of Engine

2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

Click here

3. INSTALL VALVE STEM CAP

Click here

4. INSTALL VALVE LASH ADJUSTER ASSEMBLY

Click here

5. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Click here

6. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Click here

7. INSTALL CAMSHAFT

Click here

8. INSTALL NO. 2 CAMSHAFT

Click here

9. INSTALL CAMSHAFT BEARING CAP

Click here

10. INSTALL CAMSHAFT TIMING SPROCKET

Click here

11. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Click here

12. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Click here

13. INSTALL CHAIN SUB-ASSEMBLY

HINT:

Be sure to install the chain sub-assembly with the mark plates facing away from the engine assembly.
The mark plate on the camshaft side is colored orange.
The mark plate on the crankshaft side is colored pink.

(a) Temporarily install the crankshaft pulley set bolt to the crankshaft.

(b) Install the No. 1 chain vibration damper to the cylinder head sub-assembly and cylinder block sub-assembly with the 2 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(c) Install the chain sub-assembly with the mark plates (orange) of the chain sub-assembly aligned with the timing mark (rectangle) as shown in the illustration.

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).
Do not pass the chain sub-assembly around the sprocket of the camshaft timing gear assembly. Only place it on the camshaft timing gear assembly.
Pass the chain sub-assembly through the No. 1 chain vibration damper.

*a	Place the chain sub-assembly on the sprocket
*b	Pass the chain sub-assembly through the damper
*c	Mark Plate (Orange)
*d	Timing Mark (Rectangle)
*e	Mark (Circle)

(d) Place the chain sub-assembly on the crankshaft without passing it around the crankshaft.

(e) Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to align the mark plate (orange) with timing mark, and then install the chain sub-assembly.

*a	Tension the chain sub-assembly	*b	Mark Plate (Orange)
*c	Timing Mark	-	-

HINT:

If the camshaft timing gear assembly cannot be positioned as shown in the illustration, using a wrench to hold the hexagonal portion of the camshaft, slightly rotate the camshaft timing gear assembly counterclockwise and then install the chain sub-assembly.

(f) Using a wrench to hold the hexagonal portion of the camshaft, slowly turn the camshaft timing gear assembly clockwise to tension the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.

HINT:

Make sure to turn the camshaft timing gear assembly slowly to prevent the camshaft timing sprocket from becoming misaligned.

(g) Align the mark plate (pink) with timing mark and install the chain sub-assembly to the crankshaft timing sprocket.

*a	Timing Mark
*b	Mark Plate (Pink)

(h) Check that each timing mark is at TDC (compression).

*a	Mark Plate (Orange)	*b	Mark Plate (Pink)
*c	Timing Mark	*d	Timing Mark (Rectangle)
*e	Mark (Circle)	-	-

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

(i) Remove the crankshaft pulley set bolt from the crankshaft.

14. INSTALL NO. 2 CHAIN VIBRATION DAMPER

Click here

15. INSTALL CHAIN TENSIONER SLIPPER

Click here

16. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Click here

17. INSTALL TIMING CHAIN COVER OIL SEAL

Click here

18. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Click here

19. INSTALL CRANKSHAFT PULLEY

Click here

20. INSTALL SPARK PLUG TUBE GASKET

Click here

21. INSTALL CYLINDER HEAD COVER GASKET

Click here

22. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Click here

23. INSTALL CAMSHAFT POSITION SENSOR

Click here

24. INSTALL IGNITION COIL ASSEMBLY

Click here

25. INSTALL FUEL INJECTOR ASSEMBLY

Click here

26. INSTALL NO. 1 DELIVERY PIPE SPACER

Click here

27. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here

28. INSTALL FUEL VAPOR FEED PIPE

Click here

29. INSTALL PURGE VALVE (PURGE VSV)

Click here

30. INSTALL WATER BY-PASS PIPE

Click here

31. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Click here

32. INSTALL ENGINE OIL LEVEL DIPSTICK

Click here

33. INSTALL INTAKE MANIFOLD

Click here

34. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Click here

35. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Click here

36. TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

Click here

37. TEMPORARILY INSTALL EGR PIPE ASSEMBLY

Click here

38. INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER

Click here

39. INSTALL EGR PIPE ASSEMBLY

Click here

40. INSTALL WATER OUTLET

Click here

41. INSTALL ENGINE HANGERS

Click here

42. REMOVE ENGINE FROM ENGINE STAND

Click here