Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GMAK
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 - 09/2022]
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): ECM Communication Stop Mode; 2020 - 2022 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2022]

ECM Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

ECM Communication Stop Mode

Any of the following conditions are met:

  • Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the Techstream.

    Click here 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): PROBLEM SYMPTOMS TABLE

  • Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)

    Click here 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): PROBLEM SYMPTOMS TABLE

  • Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output.

    Click here 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DTC COMBINATION TABLE 2020 MY Corolla Corolla Hatchback GR Corolla [09/2019 - 04/2020]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DTC COMBINATION TABLE 2021 - 2022 MY Corolla Corolla Hatchback GR Corolla [04/2020 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DTC COMBINATION TABLE

  • ECM main line or connector
  • Power source circuit of ECM
  • ECM ground circuit
  • ECM

WIRING DIAGRAM

for M20A-FKS
for 2ZR-FAE

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2019 - 04/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 03/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM 2020 MY Corolla Corolla Hatchback GR Corolla [03/2019 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM 2020 MY Corolla Corolla Hatchback GR Corolla [09/2019 - 04/2020]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM 2021 - 2022 MY Corolla Corolla Hatchback GR Corolla [04/2020 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK VEHICLE TYPE

(a) Check vehicle type.

Result

Proceed to

for M20A-FKS

A

for 2ZR-FAE

B

B

GO TO STEP 4

A

2.

CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the A47 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A47-8 (CANH) - A47-18 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

*a

Front view of wire harness connector

(to ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

OK

3.

CHECK ECM POWER SOURCE CIRCUIT

(a) Check the ECM power source circuit.

Click here 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: ECM Power Source Circuit

OK

REPLACE ECM 2020 MY Corolla Corolla Hatchback [01/2019 - 03/2019]; M20A-FKS (ENGINE CONTROL): ECM: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback [03/2019 - 09/2022]; M20A-FKS (ENGINE CONTROL): ECM: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.

CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the A46 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A46-13 (CANH) - A46-26 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω

*a

Front view of wire harness connector

(to ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

OK

5.

CHECK ECM POWER SOURCE CIRCUIT

(a) Check the ECM power source circuit.

Click here 2020 - 2022 MY Corolla [01/2019 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: ECM Power Source Circuit

OK

REPLACE ECM 2020 MY Corolla [01/2019 - 03/2019]; 2ZR-FAE (ENGINE CONTROL): ECM: REMOVAL 2020 - 2022 MY Corolla [03/2019 - 09/2022]; 2ZR-FAE (ENGINE CONTROL): ECM: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)