Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001GJE9 |
Model Year Start: 2020 |
Model: GR Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: FRONT SUSPENSION: FRONT SUSPENSION MEMBER: INSTALLATION; 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2022] |
INSTALLATION
PROCEDURE
1. INSTALL FRONT DIFFERENTIAL SUPPORT GUARD LH (w/ Differential Support Guard)
(a) Install the front differential support guard LH to the front suspension crossmember sub-assembly with the 2 bolts.
Torque:
18.5 N·m {189 kgf·cm, 14 ft·lbf}
NOTICE:
Make sure to install the front differential support guard LH with its arrow facing the front of the vehicle.
*a
|
Arrow
|
|
Front of the Vehicle
|
2. INSTALL HOLE PLUG
(a) Install the 4 hole plugs to the front suspension crossmember sub-assembly.
HINT:
There are 2 different shapes of hole plug.
|
|
3. INSTALL FRONT SUSPENSION MEMBER PLATE
(a) Install the 2 front suspension member plates to the front suspension crossmember sub-assembly.
4. TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
(a) Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.
5. TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
6. INSTALL ENGINE MOVING CONTROL ROD
(a) Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.
Torque:
200 N·m {2039 kgf·cm, 148 ft·lbf}
7. INSTALL FRONT STABILIZER BAR
Click here
8. INSTALL FRONT NO. 1 STABILIZER BRACKET LH
Click here
9. INSTALL FRONT NO. 1 STABILIZER BRACKET RH
HINT:
Perform the same procedure as for the LH side.
10. INSTALL STEERING LINK ASSEMBLY
Click here
11. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
(a) Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.
CAUTION:
-
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
-
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
NOTICE:
Use attachments to keep the front suspension crossmember sub-assembly level.
(b) Install the front suspension crossmember sub-assembly to the vehicle body with the 4 bolts.
Torque:
141 N·m {1438 kgf·cm, 104 ft·lbf}
(c) Lower the engine lifter.
(d) Install the engine moving control rod with the bolt.
Torque:
170 N·m {1734 kgf·cm, 125 ft·lbf}
(e) Install the 2 wire harness clamp brackets to the front suspension crossmember sub-assembly with the 2 bolts.
Torque:
13 N·m {133 kgf·cm, 10 ft·lbf}
12. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Click here
13. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
14. CONNECT TIE ROD END SUB-ASSEMBLY LH
Click here
15. CONNECT TIE ROD END SUB-ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
16. CONNECT FRONT STABILIZER LINK ASSEMBLY LH
(a) Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.
Torque:
74 N·m {755 kgf·cm, 55 ft·lbf}
NOTICE:
Do not damage the boot of the ball joint.
HINT:
If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.
17. CONNECT FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
18. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
(a) Install the rear side rail reinforcement sub-assembly LH to the front suspension crossmember sub-assembly and vehicle body with the 4 bolts.
Torque:
70 N·m {714 kgf·cm, 52 ft·lbf}
|
|
19. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
HINT:
Perform the same procedure as for the LH side.
20. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
Click here
21. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
Click here
22. INSTALL COLUMN HOLE COVER SILENCER SHEET
Click here
23. INSTALL FRONT WHEELS
Click here
24. STABILIZE SUSPENSION
(a) Lower the vehicle.
(b) Bounce the vehicle up and down several times to stabilize the suspension.
25. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
for M20A-FKS: Click here
for ZR Series Engine: Click here
26. FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
for M20A-FKS: Click here
for ZR Series Engine: Click here
27. INSTALL REAR ENGINE UNDER COVER LH
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
28. INSTALL REAR ENGINE UNDER COVER RH
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
29. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
30. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here
31. PERFORM INITIALIZATION
for Gasoline Model:
Lighting System (w/ AFS) (EXT)
|
|
|