2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P210900; Throttle/Pedal Position Sensor "A" Minimum Stop Performance; 2020 MY Corolla Corolla HV [01/2019

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001GJ77
Model Year Start: 2020	Model: Corolla	Prod Date Range: [01/2019 - 04/2020]
Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P210900; Throttle/Pedal Position Sensor "A" Minimum Stop Performance; 2020 MY Corolla Corolla HV [01/2019 - 04/2020]

DTC

P210900

Throttle/Pedal Position Sensor "A" Minimum Stop Performance

DESCRIPTION

The idle speed is controlled by the Electronic Throttle Control System (ETCS). The ETCS is comprised of a throttle actuator, which operates the throttle valve, and a throttle position sensor, which detects the opening amount of the throttle valve. The ECM controls the throttle actuator to adjust the throttle valve opening amount so that the idle speed is maintained at the target idle speed.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Memory	Note
P210900	Throttle/Pedal Position Sensor "A" Minimum Stop Performance	The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount during idle is within the normal range (up to 1.5 times the normal amount) (1 trip detection logic).	Throttle body assembly	Does not come on	DTC stored	SAE Code: P2109 DTC for Mexico Models: Applies

HINT:

The ISC learned value is the calculated intake air amount corresponding to the throttle opening amount necessary to maintain the idling speed.
This malfunction is only detected once per trip. After it has been detected once, the system will not monitor for the malfunction for the rest of the trip.
The system uses the throttle body assembly and mass air flow meter sub-assembly to detect this malfunction.

MONITOR DESCRIPTION

If there are deposits in the throttle valve, a decrease in the ISC flow rate may cause engine stall or unstable idling. Therefore, the necessary ISC flow rate for idling is maintained using the ISC learned value and feedback. The ECM stores this DTC if the ISC learned value approaches its limit. The ECM begins monitoring for the DTC detection conditions when the following preconditions are met:

The mass air flow meter sub-assembly is normal.
Atmospheric pressure is 85 kPa(abs) [12.3 psi(abs)] or higher.
The vehicle has been driven at a speed of 30 km/h (19 mph) or more at least once.
The engine coolant temperature is 45°C (113°F) or less at engine start, the engine is warmed up and conditions for ISC learning are met, or the power switch has been turned on (READY) (including when the engine is running) for 1 hour or more, the engine is warmed up and conditions for ISC learning are met.

CAUTION / NOTICE / HINT

HINT:

Since a pending DTC is not stored for this DTC, it takes time to confirm whether the malfunction has been successfully repaired by checking for this DTC. When confirming whether the malfunction has been successfully repaired, compare "ISC Learning Value" recorded in the freeze frame data with "ISC Learning Value" in the Data List after repairs have been made to save time.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P210900)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result	Proceed to
DTC P210900 is output	A
DTC P210900 and other DTCs are output	B

HINT:

If any DTCs other than P210900 are output, troubleshoot those DTCs first.

GO TO DTC CHART

2.	READ FREEZE FRAME DATA (ISC LEARNING VALUE)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Using the Techstream, check "ISC Learning Value" in the freeze frame data.

Click here

HINT:

Be sure to confirm that the freeze frame date item "ISC Learning Value" is the same as that used when confirming whether the malfunction has been successfully repaired.

3.	INSPECT THROTTLE BODY ASSEMBLY

(a) Check for foreign matter between the throttle valve and the housing.

*1	Throttle Body Assembly	*2	Bore
*3	Throttle Valve	-	-
*a	Reference	*b	Throttle Body Assembly Cross-section Diagram
*c	When valve fully opened	*d	Deposits

HINT:

The illustration is for reference only, actual parts may differ.

Result	Proceed to
Foreign matter between the throttle valve and housing	A
No foreign matter between the throttle valve and housing	B

HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly.

Click here

REPLACE THROTTLE BODY ASSEMBLY

4.	REMOVE FOREIGN MATTER (CLEAN THROTTLE BODY ASSEMBLY)

(a) Clean off any deposits inside of the throttle body assembly.

*1	Throttle Body Assembly	*2	Bore
*3	Throttle Valve	-	-
*a	Reference	*b	Throttle Body Assembly Cross-section Diagram
*c	When valve fully opened	*d	Do not directly apply cleaner
*e	Deposits	-	-

(1) Push open the throttle valve and wipe off any deposits from the valve and bore using a cloth soaked in non-residue solvent.

NOTICE:

Make sure that the cloth or your fingers do not get caught in the valve.
Make sure that foreign matter does not enter the throttle valve.
Do not directly apply non-residue solvent to the throttle body assembly or wash the throttle body assembly. Cleaning solvent may leak into the motor from the shaft and cause problems such as rust or valve movement problems.
If there is coating material on the edge of the throttle valve, be careful not to remove it.
Push the throttle valve open gently with your finger and check that the throttle valve moves smoothly.

HINT:

If the throttle valve does not open smoothly, replace the throttle body assembly.
Click here
The illustration is for reference only, actual parts may differ.

5.	READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)

(a) Perform "Inspection After Repair" after cleaning the throttle body assembly.

Click here

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Powertrain / Engine / Data List / ISC Learning Value.

Powertrain > Engine > Data List

Tester Display
ISC Learning Value

(f) According to the display on the Techstream, read the Data List.

OK:

The value of ISC Learning Value is half or less of ISC Learning Value recorded in the freeze frame data.

HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly.

Click here

END

REPLACE THROTTLE BODY ASSEMBLY