- DTC judgment completed
- System normal
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001GJ6Z |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 04/2020] |
| Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P10AA00,P219A00,P219C00-P219F00; Clogged EGR Port Imbalance Bank1; 2020 MY Corolla Corolla HV [01/2019 - 04/2020] | ||
|
DTC |
P10AA00 |
Clogged EGR Port Imbalance Bank1 |
|
DTC |
P219A00 |
Bank 1 Air-Fuel Ratio Imbalance |
|
DTC |
P219C00 |
Cylinder 1 Air-Fuel Ratio Imbalance |
|
DTC |
P219D00 |
Cylinder 2 Air-Fuel Ratio Imbalance |
|
DTC |
P219E00 |
Cylinder 3 Air-Fuel Ratio Imbalance |
|
DTC |
P219F00 |
Cylinder 4 Air-Fuel Ratio Imbalance |
DESCRIPTION
Refer to DTC P030000.
Click here
![2020 MY Corolla Corolla HV [01/2019 - 04/2020]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P030000,P030027,P030085-P030400; Random/Multiple Cylinder Misfire Detected+](/t3Portal/stylegraphics/info.gif)
Refer to DTC P040000.
Click here
Refer to DTC P219519.
Click here
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P10AA00 |
Clogged EGR Port Imbalance Bank1 |
The difference in the air fuel ratios between the cylinders exceeds the threshold when the EGR valve is open (2 trip detection logic). |
Intake manifold |
Comes on / Does not come on |
DTC stored |
|
|
P219A00 |
Bank 1 Air-Fuel Ratio Imbalance |
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P219C00 |
Cylinder 1 Air-Fuel Ratio Imbalance |
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P219D00 |
Cylinder 2 Air-Fuel Ratio Imbalance |
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P219E00 |
Cylinder 3 Air-Fuel Ratio Imbalance |
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P219F00 |
Cylinder 4 Air-Fuel Ratio Imbalance |
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
MONITOR DESCRIPTION
Fuel System Air Fuel Ratio Cylinder Imbalance Monitor
The ECM uses the air fuel ratio sensor, crankshaft position sensor and EGR valve assembly to monitor the difference in air fuel ratios between the cylinders caused by differences in fuel injection volume between the cylinders, leakage in the intake or exhaust system, etc.
When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that there is a malfunction, illuminates the MIL and stores a DTC.
EGR Port Clogged Monitoring Method: P10AA00 is stored primarily when a rich side imbalance for clogged EGR port is detected.
By comparing the air fuel ratio when EGR valve is open and closed, a clog in an EGR port can be detected. If an EGR port is clogged when the EGR valve is open, the ECM will store a DTC.
Air Fuel Ratio Sensor Monitoring Method: P219A00 is stored primarily when a rich side imbalance is detected.
When the system detects a difference in air fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the ECM determines that there is a malfunction.
Crankshaft Position Sensor Monitoring Method: P219C00, P219D00, P219E00 and/or P219F00 are stored primarily when a lean side imbalance is detected.
The system monitors the engine speed variation and when the variation becomes large, the ECM determines that there is a difference in air fuel ratios between the cylinders, which it determines to be a malfunction.
MONITOR STRATEGY
|
Related DTCs |
P10AA: Air fuel ratio cylinder imbalance monitor for clogged EGR runner P219A: Air fuel ratio cylinder imbalance monitor P219C: Air fuel ratio cylinder imbalance monitor (cylinder 1) P219D: Air fuel ratio cylinder imbalance monitor (cylinder 2) P219E: Air fuel ratio cylinder imbalance monitor (cylinder 3) P219F: Air fuel ratio cylinder imbalance monitor (cylinder 4) |
|
Required Sensors/Components (Main) |
EGR valve assembly Air fuel ratio sensor Crankshaft position sensor |
|
Required Sensors/Components (Related) |
Mass air flow meter sub-assembly Engine coolant temperature sensor |
|
Frequency of Operation |
Once per driving cycle |
|
Duration |
Approximately 20 seconds: P10AA 20 seconds: P219A 10 to 15 seconds: Others |
|
MIL Operation |
2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
P10AA, P219A
|
Monitor runs whenever the following DTCs are not stored |
P0010 (Camshaft timing oil control valve) P0011 (VVT system - advance) P0012 (VVT system - retard) P0016 (VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0101, P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air fuel ratio sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0351 - P0354 (Igniter) P0400 (EGR system) P0401 (EGR system (closed)) P0657, P0658, P2102, P2103 (Throttle actuator) |
P219C, P219D, P219E and P219F
|
Monitor runs whenever the following DTCs are not stored |
P0010 (Camshaft timing oil control valve) P0011 (VVT system - advance) P0012 (VVT system - retard) P0016 (VVT system - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0112, P0113 (Intake air temperature sensor) P0117, P0118 (Engine coolant temperature sensor) P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328 (Knock control sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0351 - P0354 (Igniter) P0400 (EGR system) P0401 (EGR system (closed)) P0657, P0658, P2102, P2103 (Throttle actuator) |
P10AA: EGR Port Clogged Monitoring Method
|
Air fuel ratio sensor status |
Activated |
|
Engine coolant temperature |
75°C (167°F) or higher |
|
Atmospheric pressure |
76 kPa(abs) [11 psi(abs)] or higher |
|
Fuel cut |
Off |
|
EGR valve assembly malfunction |
Not detected |
|
Both of the following conditions are met |
1 and 2 |
|
1. EGR on delta air fuel ratio parameter is calculated when all of the following conditions are met |
- |
|
Engine speed |
1800 rpm or higher, and less than 2600 rpm |
|
Fuel system status |
Closed loop |
|
Engine load |
40% or higher, and less than 60% |
|
EGR valve operation |
More than 20 steps |
|
2. EGR off delta air fuel ratio parameter is calculated when all of the following conditions are met |
- |
|
Engine speed |
1200 rpm or higher, and less than 2600 rpm |
|
Engine load |
40% or higher, and less than 70% |
|
EGR valve operation |
0 steps or less |
P219A: Air Fuel Ratio Sensor Monitoring Method
|
Air fuel ratio sensor status |
Activated |
|
Engine speed |
1600 rpm or more, and less than 2400 rpm |
|
Engine coolant temperature |
75°C (167°F) or higher |
|
Atmospheric pressure |
76 kPa(abs) [11 psi(abs)] or higher |
|
Fuel system status |
Closed loop |
|
Engine load |
40% or more, and less than 60% |
P219C, P219D, P219E and P219F: Crankshaft Position Sensor Monitoring Method (First Judgment)
|
Engine speed |
1200 rpm or more, and less than 1600 rpm |
|
Engine Load |
40% or more, and less than 60% |
|
Engine coolant temperature |
75°C (167°F) or higher |
|
Air fuel ratio sensor status |
Activated |
|
Fuel system status |
Closed loop |
|
Auxiliary battery voltage |
11 V or higher |
P219C, P219D, P219E and P219F: Crankshaft Position Sensor Monitoring Method (Second Judgment)
|
Vehicle speed |
Less than 3 km/h (2 mph) |
|
Engine speed |
1050 rpm or more, and less than 1350 rpm |
|
Engine coolant temperature |
75°C (167°F) or higher |
|
Air fuel ratio sensor status |
Activated |
|
Fuel system status |
Closed loop |
|
Auxiliary battery voltage |
11 V or higher |
TYPICAL MALFUNCTION THRESHOLDS
P10AA: EGR Port Clogged Monitoring Method
|
EGR port clogged monitoring method criteria |
1 or more |
P219A: Air Fuel Ratio Sensor Monitoring Method
|
Air fuel ratio sensor monitoring method criteria |
1 or more |
Crankshaft Position Sensor Monitoring Method (First Judgment)
|
Crankshaft position sensor monitoring method criteria (first judgment) |
1.5 or more |
Crankshaft Position Sensor Monitoring Method (Second Judgment)
|
Crankshaft position sensor monitoring method criteria (second judgment) |
1 or more |
HINT:
If the first judgment while driving shows that the value of Engine Speed Fluctuation Average is between 0.5 and 1.5, then second judgment will be performed when the vehicle is stopped and the engine is idling.
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here
P10AA: Fuel System / CLOGGED EGR PORT IMBALANCE B1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$97 |
Multiply by 0.001 |
No dimension |
Monitoring method using air fuel ratio sensor for clogged EGR port |
P219A: Fuel System / A/F SENSOR DETERMINATION B1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$95 |
Multiply by 0.001 |
No dimension |
Monitoring method using air fuel ratio sensor |
P219C: Fuel System / ENGINE SPEED FLUCTUATION AVERAGE #1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$85 |
Multiply by 0.001 |
No dimension |
Monitoring method using crank angle sensor |
P219D: Fuel System / ENGINE SPEED FLUCTUATION AVERAGE #2
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$86 |
Multiply by 0.001 |
No dimension |
Monitoring method using crank angle sensor |
P219E: Fuel System / ENGINE SPEED FLUCTUATION AVERAGE #3
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$87 |
Multiply by 0.001 |
No dimension |
Monitoring method using crank angle sensor |
P219F: Fuel System / ENGINE SPEED FLUCTUATION AVERAGE #4
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$81 |
$88 |
Multiply by 0.001 |
No dimension |
Monitoring method using crank angle sensor |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
P10AA00
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG) [A].
- Turn the Techstream on.
-
Put the engine in Inspection Mode (Maintenance Mode).
Click here
- Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].
- Turn the power switch off. [C]
- Turn the power switch on (READY).
-
Start the engine by depressing the accelerator pedal approximately 40% and accelerating the vehicle from 10 km/h (6 mph) to a speed between 50 and 60 km/h (31 to 37 mph) in 10 to 15 seconds [D].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine does not start, further depress the accelerator pedal.
-
Decelerate the vehicle to less than 10 km/h (6 mph) and allow the engine to stop [E].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
The vehicle can be decelerated by any method.
- Repeat steps [D] and [E] above 15 to 20 times [F].
- Enter the following menus: Powertrain / Engine / Trouble Codes [G].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P10AA00.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform the confirmation driving pattern and check the judgment result again.
-
[A] to [G]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
P219A00, P219C00, P219D00, P219E00 and P219F00
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
-
Put the engine in Inspection Mode (Maintenance Mode).
Click here
- Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
NOTICE:
Use the Techstream to clear the DTCs. (Do not disconnect the cable from negative (-) auxiliary battery terminal to clear the DTCs.)
-
With the engine running, drive the vehicle at 40 km/h (25 mph) or higher.
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
-
With the engine running, gradually accelerate the vehicle from 40 km/h (25 mph) to 80 km/h (50 mph) taking approximately 10 to 20 seconds [B].
HINT:
- Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 80 km/h (50 mph).
- If the engine stops, further depress the accelerator pedal to restart the engine.
-
With the engine running, drive the vehicle at 80 km/h (50 mph) or higher for 1 minute or more [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- Electrical load can be applied while the vehicle is driven.
- If the engine stops, further depress the accelerator pedal to restart the engine.
-
Idle the engine for 1 minute or more [D].
HINT:
Perform this step with drive (D) selected.
- Repeat steps [B] through [D] above at least 3 times [E].
- Enter the following menus: Powertrain / Engine / Trouble Codes [F].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
-
[A] to [F]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
-
With the engine running, drive the vehicle at 80 km/h (50 mph).
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
-
With the engine running, gradually accelerate the vehicle from 80 km/h (50 mph) to 100 km/h (62 mph) taking approximately 5 to 15 seconds [G].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 100 km/h (62 mph).
- If the engine stops, further depress the accelerator pedal to restart the engine.
-
With the engine running, drive the vehicle at 100 km/h (62 mph) or higher for 1 minute or more [H].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- Electrical load can be applied while the vehicle is driven.
- If the engine stops, further depress the accelerator pedal to restart the engine.
-
Idle the engine for 1 minute or more [I].
HINT:
Perform this step with drive (D) selected.
- Repeat steps [G] through [I] above at least 2 times [J].
- Enter the following menus: Powertrain / Engine / Trouble Codes [K].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P219A00, P219C00, P219D00, P219E00 or P219F00.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the confirmation driving pattern and check the judgment result again.
-
[A] to [K]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to Fuel Injector Circuit.
Click here
CAUTION / NOTICE / HINT
HINT:
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric air fuel ratio. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK ANY OTHER DTCS OUTPUT |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 is output |
A |
|
DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 and other DTCs are output |
B |
HINT:
If any DTCs other than DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 are output, troubleshoot those DTCs first.
| B |
|
|
|
2. |
READ VALUE USING TECHSTREAM (FREEZE FRAME DATA) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click here
Freeze Frame Data Items for DTC P10AA00, P219A00, P219C00, P219D00, P219E00 and/or P219F00:
- Vehicle Speed
- Engine Speed
- Calculate Load
- Short FT B1S1
- Long FT B1S1
- Misfire Count Cylinder #1 to #4
HINT:
When the sum of Short FT B1S1 and Long FT B1S1 is positive, the engine is running lean, and when the sum is negative, the engine is running rich.
|
Air Fuel Ratio Sensor Monitoring Method (P219A00) |
Crankshaft Position Sensor Monitoring Method (P219C00, P219D00, P219E00 and P219F00) |
EGR Port Clogged Monitoring Method (P10AA00) |
Note |
|---|---|---|---|
|
- |
- |
DTC is output |
Detected by EGR Port Clogged Monitoring Method.*1 |
|
DTC is output |
DTC is output (Only one DTC relating to a single cylinder is output) |
DTC is not output |
Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected |
|
DTC is output |
DTCs are output (Multiple DTCs relating to multiple cylinders are output) |
DTC is not output |
Malfunctioning of cylinders except ones detected by Crankshaft Position Sensor Monitoring Method is primarily suspected.*2 |
|
DTC is not output |
DTCs are output |
DTC is not output |
Malfunctioning of cylinders detected by Crankshaft Position Sensor Monitoring Method is primarily suspected. |
|
DTC is output |
DTCs are not output |
DTC is not output |
Malfunctioning of the bank detected by Air Fuel Ratio Sensor Monitoring Method is primarily suspected. |
*1: Even if other DTCs are output, it is likely that an EGR port is clogged.
*2: When any air fuel ratio imbalance is detected, the ECM will perform air fuel ratio feedback control to make the air fuel ratio close to the stoichiometric air fuel ratio. This may result in an air fuel ratio imbalance of normal cylinders and DTCs may be stored.
|
|
3. |
READ OUTPUT DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Click here
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Drive the vehicle in accordance with Confirmation Driving Pattern.
HINT:
- If any misfire count (Misfire Count Cylinder #1 to #4) increases while idling or driving the vehicle, proceed to step 7.
- Perform inspections while focusing on the cylinder whose misfire count has increased.
- Perform the confirmation driving patterns for both DTC P10AA00 and P219A00.
(f) Enter the following menus: Powertrain / Engine / Trouble Codes.
(g) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P10AA00 is output |
A |
|
DTC P219A00 is output |
B |
|
DTC P219A00 and P219C00, P219D00, P219E00 or P219F00 are output |
C |
|
DTC P219C00, P219D00, P219E00 and/or P219F00 is output |
| B |
|
| C |
|
|
|
4. |
REPLACE INTAKE MANIFOLD |
(a) Replace the intake manifold.
Click here
HINT:
Perform "Inspection After Repair" after replacing the intake system.
Click here
| NEXT |
|
|
5. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Click here
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Start the engine and warm it up.
HINT:
The A/C switch and all accessories should be off and park (P) or neutral (N) should be selected.
(f) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / Misfire Count Cylinder #1 to #4.
HINT:
When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 7 (Check Intake System).
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Injection Volume |
|
Data List Display |
|---|
|
Misfire Count Cylinder #1 |
|
Misfire Count Cylinder #2 |
|
Misfire Count Cylinder #3 |
|
Misfire Count Cylinder #4 |
(g) According to the display on the Techstream, perform the Active Test with the engine idling.
(h) Check the misfire counts (Misfire Count Cylinder #1 to #4) while decreasing the injection volume in 5% increments.
The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.
|
|
6. |
CHECK FOR EXHAUST GAS LEAK |
(a) Check for exhaust gas leaks.
OK:
No gas leaks in exhaust system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click here
| NG |
|
REPAIR OR REPLACE EXHAUST SYSTEM |
|
|
7. |
CHECK INTAKE SYSTEM |
(a) Check the intake system for vacuum leaks.
Click here
OK:
No leaks from the intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click here
| NG |
|
REPAIR OR REPLACE INTAKE SYSTEM |
|
|
8. |
INSPECT SPARK PLUG |
(a) Inspect the spark plug of the cylinder causing the imbalance.
Click here
HINT:
Perform "Inspection After Repair" after replacing the spark plug.
Click here
| NG |
|
|
|
9. |
CHECK FOR SPARK (SPARK TEST) |
(a) Perform a spark test.
Click here
HINT:
- If the result of the spark test is normal, proceed to the next step.
-
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click here
|
|
10. |
CHECK CYLINDER COMPRESSION PRESSURE |
(a) Measure the cylinder compression pressure of the misfiring cylinder.
Click here
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click here
| NG |
|
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION |
|
|
11. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY) |
|
*a |
Front view of wire harness connector (to Fuel Injector Assembly) |
(a) Disconnect the fuel injector assembly connector.
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C33-1 - Body ground |
Power switch on (IG) |
11 to 14 V |
|
C34-1 - Body ground |
Power switch on (IG) |
11 to 14 V |
|
C35-1 - Body ground |
Power switch on (IG) |
11 to 14 V |
|
C36-1 - Body ground |
Power switch on (IG) |
11 to 14 V |
| NG |
|
|
|
12. |
CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE |
(a) Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click here
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click here
| NG |
|
|
|
13. |
CHECK FOR CAUSE OF FAILURE |
(a) If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
(b) Check the intake valve for deposits.
HINT:
As the DTC may have been stored due to deposits an the intake valve, remove the cylinder head and check the intake valves.
|
|
14. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
15. |
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
HINT:
Perform the appropriate confirmation driving patterns for the DTCs that were output.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Check for DTCs.
Powertrain > Engine > Trouble Codes
OK:
DTCs are not output.
| NEXT |
|
END |
|
|