Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GJ6S
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 04/2020]
Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P060B49; Internal Control Module A/D Processing Performance Internal Electronic Failure; 2020 MY Corolla Corolla HV [01/2019 - 04/2020]

DTC

P060B49

Internal Control Module A/D Processing Performance Internal Electronic Failure

MONITOR DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P060B49

Internal Control Module A/D Processing Performance Internal Electronic Failure

ECM main CPU communication error (1 trip detection logic).

ECM

Comes on

DTC stored

  • SAE Code: P060B
  • DTC for Mexico Models: Applies

MONITOR STRATEGY

Related DTCs

P060B: Internal control module A/D processing performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

-

Frequency of Operation

Continuous

Duration

2 times

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

TYPICAL MALFUNCTION THRESHOLDS

AD converter

Fail

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the power switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) auxiliary battery terminal.
  10. Connect the Techstream to the DLC3.
  11. Turn the power switch on (IG).
  12. Turn the Techstream on.
  13. Wait 16 seconds or more [A].
  14. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  15. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P060B49.
  18. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • [A] to [B]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off.

NEXT

2.

READ OUTPUT DTC (DTC P060B49)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Wait 16 seconds or more.

(g) Enter the following menus: Powertrain / Engine / Trouble Codes.

(h) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P060B49 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM