Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GJ6Q
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 04/2020]
Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P060796; Control Module Performance Bank 1 Component Internal Failure; 2020 MY Corolla Corolla HV [01/2019 - 04/2020]

DTC

P060796

Control Module Performance Bank 1 Component Internal Failure

MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P060796

Control Module Performance Bank 1 Component Internal Failure

Either of the following conditions is met (1 trip detection logic):

  • The ECM CPUs malfunction.
  • The heated oxygen sensor transistor (built into the ECM) malfunctions.
  • ECM
  • Heated oxygen sensor (sensor 2)
  • Exhaust gas leak

Comes on

DTC stored
  • SAE Code: P0607
  • DTC for Mexico Models: Does not apply

MONITOR STRATEGY

Related DTCs

P0607: Control module performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

Heated oxygen sensor

Frequency of Operation

Continuous

Duration

60 seconds

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor transistors

Fail

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Stop the engine for 30 minutes or more [A].
  2. Connect the Techstream to the DLC3.
  3. Turn the power switch on (IG) [B].
  4. Turn the Techstream on.
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Turn the power switch off and wait for at least 30 seconds.
  7. Turn the power switch on (IG) [C].
  8. Turn the Techstream on.
  9. Put the engine in Inspection Mode (Maintenance Mode).

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

  10. Start the engine and wait 2 minutes [D].
  11. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [E].
  12. Idle the engine for 1 minute [F].
  13. With the engine running, accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:

    If the engine stops, further depress the accelerator pedal to restart the engine.

  14. With the engine running, drive the vehicle at 60 to 80 km/h (37 to 50 mph) for 5 minutes or more [H].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:

    If the engine stops, further depress the accelerator pedal to restart the engine.

  15. Enter the following menus: Powertrain / Engine / Trouble Codes [I].
  16. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  18. Input the DTC: P060796, P013611, P013613, P013614, P013615, P013617 or P013623.
  19. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [E] through [I] again.
    • [A] to [I]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P060796)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

P060796 and P013611, P013613, P013614, P013615, P013617 or P013623 are output

A

P060796 is output

B
B

GO TO STEP 3

A

2.

INSPECT DTC (P013611, P013613, P013614, P013615, P013617 OR P013623)

(a) Refer to the P013611, P013613, P013614, P013615, P013617 or P013623 flowchart.

HINT:

  • If P013611, P013613, P013614, P013615, P013617 or P013623 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

    Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P013611,P013613,P013614,P013615,P013617,P013623,P013A00; O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground

  • If DTC P060796 and P013611, P013613, P013614, P013615, P013617 or P013623 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).
NEXT

GO TO STEP 7

3.

CHECK FOR EXHAUST GAS LEAK

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Put the engine in Inspection Mode (Maintenance Mode).

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility

Tester Display

Inspection Mode

(e) Start the engine.

(f) Allow the engine to idle, and then rev the engine.

(g) Check for exhaust gas leaks around the heated oxygen sensor.

If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

HINT:

  • If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.
  • If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.
  • Perform "Inspection After Repair" after repairing or replacing the exhaust system.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

NEXT

4.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off and wait for at least 30 seconds.

NEXT

5.

PERFORM CONFIRMATION DRIVING PATTERN

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Put the engine in Inspection Mode (Maintenance Mode).

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility

Tester Display

Inspection Mode

(e) Start the engine.

(f) Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

(g) Perform the driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.

(1) With the engine running, accelerate the vehicle until 80 km/h (50 mph) and stop the vehicle.

(2) With the engine running, drive the vehicle between 60 to 80 km/h (37 to 50 mph) for 5 minutes.

(h) Enter the following menus: Powertrain / Engine / Trouble Codes.

(i) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

P013611, P013613, P013614, P013615, P013617, P013623 and/or P060796 are output

A

Only P060796 is output

B

DTCs are not output

C
B

REPLACE ECM

C

GO TO STEP 7

A

6.

INSPECT DTC (P013611, P013613, P013614, P013615, P013617 OR P013623)

(a) Refer to the P013611, P013613, P013614, P013615, P013617 or P013623 flowchart.

HINT:

  • If P013611, P013613, P013614, P013615, P013617 or P013623 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

    Click here 2020 MY Corolla Corolla HV [01/2019 - 04/2020]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P013611,P013613,P013614,P013615,P013617,P013623,P013A00; O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground

  • If DTC P060796 and P013611, P013613, P013614, P013615, P013617 or P013623 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).
NEXT

7.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off and wait for 30 minutes.

NEXT

8.

INSPECT ECM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Put the engine in Inspection Mode (Maintenance Mode).

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility

Tester Display

Inspection Mode

(e) Start the engine and allow it to idle for 2 minutes.

(f) Enter the following menus: Powertrain / Engine / Trouble Codes.

(g) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P060796 is output

B
A

END
B

REPLACE ECM