- DTC judgment completed
- System normal
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001GJ56 |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 04/2020] |
| Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P001100,P001200; Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1; 2020 MY Corolla Corolla HV [01/2019 - 04/2020] | ||
|
DTC |
P001100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
|
DTC |
P001200 |
Camshaft Position "A" - Timing Over-Retarded Bank 1 |
DESCRIPTION
Refer to DTC P001013.
Click here
![2020 MY Corolla Corolla HV [01/2019 - 04/2020]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P001013; A Camshaft Position Actuator Bank 1 Circuit Open+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P001100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P001200 |
Camshaft Position "A" - Timing Over-Retarded Bank 1 |
Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic). |
|
Comes on |
DTC stored |
|
MONITOR DESCRIPTION
The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve assembly and VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.
- Example:
-
A DTC is stored when the following conditions are met:
- It takes 5 seconds or more to change the valve timing by 5°CA.
- After the above condition is met, the camshaft timing oil control valve assembly is forcibly activated for 9.5 seconds or more.
DTC P001100 (Advanced Camshaft Timing) is subject to 1 trip detection logic.
DTC P001200 (Retarded Camshaft Timing) is subject to 2 trip detection logic.
These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly.
MONITOR STRATEGY
|
Related DTCs |
P0011: Advanced camshaft timing P0012: Retarded camshaft timing |
|
Required Sensors/Components (Main) |
Camshaft timing oil control valve assembly Camshaft timing gear assembly |
|
Required Sensors/Components (Related) |
Crankshaft position sensor Camshaft position sensor Engine coolant temperature sensor |
|
Frequency of Operation |
Continuous |
|
Duration |
Within 10 seconds |
|
MIL Operation |
Advanced camshaft timing: Immediate Retarded camshaft timing: 2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
P0010 (Camshaft timing oil control valve) P0016 (VVT system - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) |
|
Auxiliary battery voltage |
11 V or higher |
|
Engine speed |
500 to 4000 rpm |
|
Engine coolant temperature |
75 to 100°C (167 to 212°F) |
TYPICAL MALFUNCTION THRESHOLDS
P0011: Advanced Camshaft Timing
|
Both of the following conditions are met |
- |
|
Deviation of actual valve timing and target valve timing |
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
|
Valve timing |
No change at advanced valve timing |
P0012: Retarded Camshaft Timing
|
Both of the following conditions are met |
- |
|
Deviation of actual valve timing and target valve timing |
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
|
Valve timing |
No change at retarded valve timing |
If the difference between the target and actual camshaft timing is greater than the specified value, the ECM operates the VVT actuator (camshaft timing oil control valve assembly) for 9.5 seconds or more by applying and releasing oil pressure. Then, the ECM monitors the change in camshaft timing for 9.5 seconds.
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here
P0011, P0012: Exhaust Gas Recirculation/VVT / IN VVT STUCK B1
|
Monitor ID |
Test ID |
Scaling |
Unit |
Description |
|---|---|---|---|---|
|
$35 |
$81 |
Multiply by 0.01 |
Second |
Forced movement of oil control actuator time |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
HINT:
-
If P001100 was output:
Clear the DTC without using the Techstream.
-
If P001200 was output:
Clear the DTC using the Techstream.
-
If P001100 was output:
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG) [A].
- Turn the Techstream.
-
Put the engine in Inspection Mode (Maintenance Mode).
Click here
- Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [B].
-
With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
- Idle the engine for 100 seconds or more [D].
- Enter the following menus: Powertrain / Engine / Trouble Codes [E].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P001100 or P001200.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [F] through [H].
-
[A] to [E]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
-
With the engine running, accelerate the vehicle to 75 km/h (46 mph) or more by depressing the accelerator pedal for 10 seconds or more [F].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
- Idle the engine for 100 seconds or more [G].
- Enter the following menus: Powertrain / Engine / Trouble Codes [H].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
-
Check the DTC judgment result again.
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
-
[A] to [H]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P001013.
Click here
CAUTION / NOTICE / HINT
HINT:
- DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in parts of the system. The DTC will remain stored even if the system returns to normal after a short time. The foreign matter may then be captured by the oil filter.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100 OR P001200) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P001100 or P001200 is output |
A |
|
DTC P001100 or P001200 and other DTCs are output |
B |
HINT:
If any DTCs other than P001100 or P001200 are output, troubleshoot those DTCs first.
| B |
|
|
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Click here
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1.
Powertrain > Engine > Active Test
|
Tester Display |
|---|
|
Control the Intake VVT OCV Duty Ratio Bank 1 |
(g) Check the engine speed while operating the camshaft timing oil control valve assembly using the Techstream.
OK:
|
Techstream Operation |
Specified Condition |
|---|---|
|
0% |
Normal engine speed |
|
100% |
Engine idles roughly or stalls |
HINT:
- Test not possible with park (P) selected during charge control. Select neutral (N) to perform test.
- If DTCs are stored after the Active Test, clear the DTCs.
| NG |
|
|
|
3. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
HINT:
-
If P001100 was output:
Clear the DTC without using the Techstream.
-
If P001200 was output:
Clear the DTC using the Techstream.
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
4. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P001100 or P001200 is output |
B |
HINT:
DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in parts of the system. The DTC will remain stored even if the system returns to normal after a short time. The foreign matter may then be captured by the oil filter.
| A |
|
| B |
|
|
5. |
INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
(a) Inspect the camshaft timing oil control valve assembly.
Click here
| NG |
|
|
|
6. |
CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
(a) Remove the cylinder head cover sub-assembly.
|
*a |
39.5° |
*b |
Timing Mark |
|
*c |
"0" Timing Mark |
*d |
Groove |
(b) Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain or belt cover sub-assembly.
(c) Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.
HINT:
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
OK:
Timing marks on camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.
HINT:
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
| NG |
|
|
|
7. |
INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
(a) Inspect the camshaft timing gear assembly.
Click here
HINT:
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click here
| NG |
|
|
|
8. |
INSPECT OIL CONTROL VALVE FILTER |
|
*1 |
Oil Control Valve Filter |
(a) Remove the oil control valve filter.
Click here
(b) Check that the filter is not clogged.
OK:
Filter is not clogged.
| OK |
|
| NG |
|
|
9. |
CHECK ENGINE MECHANICAL SYSTEM |
(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.
Click here
| NG |
|
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA |
|
|
10. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
HINT:
-
If P001100 was output:
Clear the DTC without using the Techstream.
-
If P001200 was output:
Clear the DTC using the Techstream.
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
11. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTC P001100 or P001200 is output |
B |
| A |
|
| B |
|
|
|