| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001GIK7 |
| Model Year Start: 2020 | Model: Corolla Hatchback | Prod Date Range: [01/2019 - 03/2019] |
| Title: PARKING BRAKE: PARKING BRAKE CABLE (except G16E-GTS): REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 03/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during parking brake cable assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System (for Gasoline Model) |
|
|
Pre-collision System (for Gasoline Model) |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System (for Hatchback, Gasoline Model) |
|
|
NOTICE:
- After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
CAUTION / NOTICE / HINT
HINT:
- The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
- Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.
PROCEDURE
1. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY
Click here
![2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; PARKING BRAKE: PARKING BRAKE LEVER: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE PARKING BRAKE CABLE END STOPPER
|
(a) Disengage the 2 claws to separate the No. 1 parking brake cable assembly from the parking brake cable end stopper. |
|
|
(b) Disengage the 2 claws to remove the parking brake cable end stopper and No. 1 parking brake cable assembly from the parking brake equalizer. |
|
3. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY
|
(a) Remove the No. 1 wire adjusting nut. |
|
|
(b) Pull up the parking brake lever sub-assembly claw. NOTICE: Do not damage the No. 1 parking brake cable assembly. |
|
(c) Remove the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.
4. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)
Click here
5. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
|
(a) Remove the 3 nuts and front No. 1 floor heat insulator. |
|
6. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
|
(a) Remove the 4 clips. |
|
(b) Remove the 2 nuts and front No. 2 floor heat insulator.
7. REMOVE PARKING BRAKE LEVER PROTECTOR
|
(a) Remove the parking brake lever protector from the No. 3 parking brake cable assembly. |
|
8. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY
(a) Remove the 4 bolts and nut, and separate the No. 3 parking brake cable assembly.
|
(b) Pull out the No. 3 parking brake cable assembly to the outside of the vehicle body. |
|
|
(c) Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly. |
|
|
(d) Disengage the clip and remove the No. 3 parking brake cable assembly. |
|
|
|