Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GIK7
Model Year Start: 2020 Model: Corolla Hatchback Prod Date Range: [01/2019 - 03/2019]
Title: PARKING BRAKE: PARKING BRAKE CABLE (except G16E-GTS): REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 03/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during parking brake cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*1: for Hatchback

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System (for Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System (for Gasoline Model)

Lighting System (w/ AFS)(EXT)

Initialize back door lock*1

Power Door Lock Control System (for Hatchback, Gasoline Model)

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

CAUTION / NOTICE / HINT

HINT:

  • The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
  • Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.

PROCEDURE

1. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; PARKING BRAKE: PARKING BRAKE LEVER: REMOVAL

2. REMOVE PARKING BRAKE CABLE END STOPPER

(a) Disengage the 2 claws to separate the No. 1 parking brake cable assembly from the parking brake cable end stopper.

(b) Disengage the 2 claws to remove the parking brake cable end stopper and No. 1 parking brake cable assembly from the parking brake equalizer.

3. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

(a) Remove the No. 1 wire adjusting nut.

(b) Pull up the parking brake lever sub-assembly claw.

NOTICE:

Do not damage the No. 1 parking brake cable assembly.

(c) Remove the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.

4. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (INTAKE / EXHAUST): EXHAUST PIPE: REMOVAL

5. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

(a) Remove the 3 nuts and front No. 1 floor heat insulator.

6. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

(a) Remove the 4 clips.

*a

Nut

*b

Clip

(b) Remove the 2 nuts and front No. 2 floor heat insulator.

7. REMOVE PARKING BRAKE LEVER PROTECTOR

(a) Remove the parking brake lever protector from the No. 3 parking brake cable assembly.

8. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Remove the 4 bolts and nut, and separate the No. 3 parking brake cable assembly.

(b) Pull out the No. 3 parking brake cable assembly to the outside of the vehicle body.

(c) Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

(d) Disengage the clip and remove the No. 3 parking brake cable assembly.

*1

Rear Disc Brake Cylinder Assembly

*a

Clip