| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001GHYJ |
| Model Year Start: 2020 | Model: Corolla Hatchback | Prod Date Range: [01/2019 - 11/2022] |
| Title: AXLE AND DIFFERENTIAL: REAR AXLE HUB BOLT (for Double Wishbone Type Suspension 2WD without Electric Parking Brake): REPLACEMENT; 2020 - 2023 MY Corolla Corolla Hatchback Corolla HV [01/2019 - 11/2022] | ||
REPLACEMENT
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR WHEEL
Click here
![2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; MAINTENANCE: TIRE AND WHEEL: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. LOOSEN NO. 1 WIRE ADJUSTING NUT
|
(a) Disengage the 2 claws, 2 clips and 3 guides to separate the No. 1 box panel. |
|
(b) Disconnect the 2 connectors and remove the No. 1 box panel.
(c) Release the parking brake lever lock and return it to its off position.
|
(d) Loosen the No. 1 wire adjusting nut to completely release the parking brake cable as shown in the illustration. NOTICE: Do not remove the No. 1 wire adjusting nut. |
|
3. REMOVE PARKING BRAKE LEVER PROTECTOR
Click here
4. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY
Click here
5. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
(a) Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.
(b) Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.
NOTICE:
Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.
6. REMOVE REAR DISC
Click here
7. REMOVE REAR AXLE HUB BOLT
|
(a) Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration. Recommended Service Nut: Thread diameter: 12.0 mm (0.472 in.) Thread pitch: 1.5 mm (0.0591 in.) NOTICE: Install the service nuts to prevent damage to the rear axle hub bolts. |
|
(b) Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
SST: 09611-12010
NOTICE:
Do not damage the threads of the rear axle hub bolts.
8. INSTALL REAR AXLE HUB BOLT
|
(a) Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly. |
|
(b) Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Recommended Service Nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
HINT:
Recommended washer thickness is 5 mm (0.197 in.) or more.
(c) Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
NOTICE:
- Install the service nuts to prevent damage to the rear axle hub bolts.
- Do not damage the threads of the rear axle hub bolts.
(d) Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
9. INSTALL REAR DISC
Click here
10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
(a) Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.
Torque:
107 N·m {1091 kgf·cm, 79 ft·lbf}
(b) Install the rear flexible hose to the rear flexible hose bracket with the bolt.
Torque:
29 N·m {296 kgf·cm, 21 ft·lbf}
11. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
Click here
12. INSTALL PARKING BRAKE LEVER PROTECTOR
Click here
13. ADJUST PARKING BRAKE
Click here
14. INSTALL REAR WHEEL
Click here
|
|