Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001GH98
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 11/2022]
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION; 2020 - 2023 MY Corolla [01/2019 - 11/2022]

INITIALIZATION

Inspection After Repair

Perform learning value reset and idle learning after replacing or servicing parts related to engine operation. Details on procedures required are indicated by an asterisk and a number, and are explained in detail following the table.

Part Replaced

Engine Operation

Learning Value Reset*1

Idle Learning
  • Throttle body assembly*4
  • Cleaning the deposits from the throttle body assembly*4

-

○

○*2

Engine assembly

-

○

○*2

Continuously variable valve lift controller assembly

-

○

○*3
  • Cylinder head sub-assembly
  • Camshaft housing sub-assembly
  • Camshaft timing gear assembly
  • Camshaft timing exhaust gear assembly
  • Piston or piston ring
  • Mass air flow meter sub-assembly
  • Fuel injector assembly
  • Fuel pump
  • Air fuel ratio sensor
  • Heated oxygen sensor
  • Engine coolant temperature sensor
  • Spark plug
  • Ignition coil assembly
  • Air leaks from intake system
  • Gas leaks from exhaust system

Confirm the following:

Perform learning value reset and idle learning when one or more of the following conditions is met.

  1. A DTC was output before component replacement.
  2. An air fuel ratio learned value (one of A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1 or A/F Learn Value High #1) displayed in the Data List was higher than +/- 15% before component replacement.
  3. Starting failure, rough idle, or engine stalls after component replacement.

○

○*2

The items in the list above do not apply.

-

-

Knock control sensor*5

-

-

-
  • ○: Necessary.
  • -: Unnecessary.

NOTICE:

Engine learned values cannot be reset by disconnecting the battery negative (-) terminal or removing the EFI-MAIN NO. 1 and ETCS fuses.

  • *1: Learning Value Reset
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Value Reset.
    5. Confirm the following conditions as instructed on the screen.
      • - Ignition switch ON
      • - Engine stopped
      • - Battery voltage is higher than 9 V
    6. After confirming, select "Next" and initialize the learned value.

      HINT:

      If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.

    7. After the completion of learned value initialization, confirm the air fuel ratio learned values (A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1 and A/F Learn Value High #1) in the Data List.

      If 0 is displayed for all the air fuel ratio learned values, initialization has completed correctly.

      If a value other than 0 is displayed for one of the air fuel ratio learned values, perform initialization again. After initialization, confirm the air fuel ratio learned values. If a value other than 0 is displayed, replace the ECM.

  • *2: Idle Learning
    1. Turn the ignition switch off and wait for at least 30 seconds.
    2. Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.

      HINT:

      Learning starts when the engine coolant temperature is 80°C (176°F) or higher.

    3. After the engine is warmed up, allow it to idle for 5 minutes with the air conditioning and all accessories off.
    4. Confirm that the idle speed is within the standard range.

      Standard:

      Engine Idle Speed
      • 600 to 700 rpm (for Manual Transaxle models)
      • 700 to 800 rpm (for CVT models)

      HINT:

      • Be sure to perform this step with all accessories off.
      • Make sure that the shift lever is in P or N (neutral).
  • *3: Minimum Valve Lift Learning
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON (do not start the engine).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VALVEMATIC(ENG OFF) / Data List / VALVEMATIC Current Angle.
    5. Change the Activate the VALVEMATIC(ENG OFF) to "Low".
    6. Confirm that the "VALVEMATIC Current Angle" value remains at the standard.

      Standard:

      VALVEMATIC Current Angle

      106 deg(CA)
  • *4: Perform memory reset and idle learning after replacing the throttle body assembly or cleaning deposits from the throttle body assembly.

    After that, check the idle speed. If the value is out of the specified range, perform the procedure below.

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:

    History information for driving and stopping is necessary to update idle learning.

    1. Warm up the engine (engine coolant temperature is 80°C (176°F) or higher, air conditioning and all accessories are off) [A].
    2. Drive the vehicle at 10 km/h (6 mph) or more [B].
    3. Idle the engine for 20 seconds or more [C].
    4. Repeat procedure [B] and [C], and check that the idle speed is within the specified range [D].

      Standard:

      Engine Idle Speed
      • 600 to 700 rpm (for Manual Transaxle models)
      • 700 to 800 rpm (for CVT models)

      HINT:

      • Be sure to perform this step with all accessories off.
      • Make sure that the shift lever is in P or N (neutral).
      • If the idle speed is still out of the specified range, repeat procedure [B] and [C] until the idle speed is within the specified range [E].
  • *5: Drive the vehicle for a short while after replacing the knock control sensor, and check if knocking occurs. If knocking occurs, drive the vehicle until knocking stops.