Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001GFTN
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 04/2020]
Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P044313; Evaporative Emission System Purge Control Valve "A" Circuit Open; 2020 MY Corolla Corolla HV [01/2019 - 04/2020]

DTC

P044313

Evaporative Emission System Purge Control Valve "A" Circuit Open

DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel routed to the cylinders is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P044313

Evaporative Emission System Purge Control Valve "A" Circuit Open

Both of the following conditions are met for 10 seconds or more (1 trip detection logic):

  • The purge VSV operation duty signal is 5 to 95%.
  • The target control value and actual control value do not match.
  • Open or short in purge VSV circuit
  • Purge VSV
  • ECM

Comes on

DTC stored

  • SAE Code: P0443
  • DTC for Mexico Models: Applies (Mexico models only)

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG).
  7. Turn the Techstream on.
  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE

  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

    HINT:

    The A/C switch and all accessories should be off.

  10. Idle the engine for 15 minutes or more [B].

    HINT:

    Check the Data List item "EVAP (Purge) VSV". When the value of this item is between 5 and 95%, the judgment will be performed.

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  12. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  14. Input the DTC: P044313.
  15. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system is malfunctioning.
    • If the judgment result shows INCOMPLETE, perform steps [D] and [E].
  16. With the engine running, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:

    If the engine stops, further depress the accelerator pedal to restart the engine.

  17. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  18. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  19. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  20. Input the DTC: P044313.
  21. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system is malfunctioning.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE EVAP PURGE VSV)

*a

VSV is on

*b

VSV is off

(a) Disconnect the fuel vapor feed hose assembly (canister side) of the purge VSV.

(b) Connect the Techstream to the DLC3.

(c) Turn the power switch on (IG).

(d) Turn the Techstream on.

(e) Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility

Tester Display

Inspection Mode

(f) Start the engine.

(g) Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test

Tester Display

Activate the EVAP Purge VSV

(h) When the purge VSV is operated using the Techstream, check whether the port of the purge VSV applies suction your finger.

OK:

Techstream Operation

Specified Condition

ON

Purge VSV port applies suction to finger

OFF

Purge VSV port applies no suction to finger

HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

OK

CHECK FOR INTERMITTENT PROBLEMS

NG

2.

INSPECT PURGE VSV

(a) Inspect the purge VSV.

Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (EMISSION CONTROL): PURGE VALVE: INSPECTION

NG

REPLACE PURGE VSV

OK

3.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

*a

Front view of wire harness connector

(to Purge VSV)

(a) Disconnect the purge VSV connector.

(b) Turn the power switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

C29-2 - Body ground

Power switch on (IG)

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - PURGE VSV)

OK

4.

CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

(a) Disconnect the purge VSV connector.

(b) Disconnect the ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C29-1 - C77-33 (PRG)

Always

Below 1 Ω

C29-1 or C77-33 (PRG) - Body ground and other terminals

Always

10 kΩ or higher

OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR