| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001GEUZ |
| Model Year Start: 2020 | Model: GR Corolla | Prod Date Range: [01/2019 - 03/2019] |
| Title: DOOR / HATCH: LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY: REMOVAL; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during luggage door lock control cable sub-assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: for Hatchback | |||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System |
|
|
Pre-collision System |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock*1 |
Power Door Lock Control System |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 04/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
- After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Control System |
|
|
Pre-collision System |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click here
for Power Seat:
Click here
2. REMOVE REAR SEAT ASSEMBLY
Click here
3. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here
4. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)
Click here
5. REMOVE REAR UNDER SIDE COVER LH (for HV Model)
Click here
6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
7. REMOVE REAR SEAT SIDE GARNISH LH
Click here
8. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
11. REMOVE LAP BELT OUTER ANCHOR COVER
Click here
12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
13. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here
14. REMOVE ROOF SIDE INNER GARNISH LH
Click here
15. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
16. REMOVE CENTER STOP LIGHT SET
Click here
17. REMOVE PACKAGE TRAY TRIM BRACKET LH
Click here
18. REMOVE PACKAGE TRAY TRIM BRACKET RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Click here
20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
21. REMOVE LUGGAGE COMPARTMENT DOOR COVER
Click here
22. REMOVE SPARE WHEEL COVER
|
(a) Remove the spare wheel cover. |
|
23. REMOVE REAR FLOOR FINISH PLATE
|
(a) Remove the 2 clips. |
|
(b) Disengage the 2 clips, 2 claws and 6 guides to remove the rear floor finish plate as shown in the illustration.
|
Remove in this Direction |
24. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH
|
(a) Using a clip remover, remove the clip. |
|
(b) Using a clip remover, remove the clip (A), 5 clips (B) and luggage compartment trim cover assembly LH.
|
Clip (A) |
|
Clip (B) |
25. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
(a) Remove the screw. |
|
|
(b) Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration. |
|
|
(c) w/o Fuel Lid Opener Switch: (1) Disconnect the fuel lid lock control cable sub-assembly. |
|
(d) Disconnect the luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
26. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY
(a) Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.
(b) w/o Wireless Door Lock System:
|
(1) Disconnect the luggage door lock control cable sub-assembly. |
|
(c) w/ Wireless Door Lock System:
|
(1) Disengage the claw as shown in the illustration. |
|
|
(2) Disconnect the luggage door lock control cable sub-assembly. |
|
|
(d) Disengage each clamp and disconnect the luggage door lock control cable sub-assembly. |
|
(e) Disengage each clamp and remove the luggage door lock control cable sub-assembly.
|
|