Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001GCQB |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Auxiliary battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
NOTICE:
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
PROCEDURE
1. PRECAUTION
Click here
2. REMOVE SERVICE PLUG GRIP
Click here
3. DISCONNECT ENGINE WIRE
Click here
4. REMOVE CONNECTOR COVER ASSEMBLY
Click here
5. CHECK TERMINAL VOLTAGE
Click here
6. INSTALL CONNECTOR COVER ASSEMBLY
Click here
7. CONNECT ENGINE WIRE
Click here
8. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY
Click here
9. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
10. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
11. REMOVE REAR DOOR SCUFF PLATE LH
Click here
12. REMOVE REAR UNDER SIDE COVER LH
Click here
13. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE REAR UNDER SIDE COVER RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE REAR UNDER COVER
Click here
16. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Click here
17. REMOVE BATTERY COOLING BLOWER ASSEMBLY
Click here
18. REMOVE NO. 1 HV BATTERY COVER PANEL RH
Click here
19. DISCONNECT FLOOR UNDER WIRE
Click here
20. DISCONNECT FLOOR WIRE
Click here
21. REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT
Click here
22. DISCONNECT FLOOR WIRE
Click here
23. REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Click here
24. REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Remove the bolt and disconnect the electric vehicle battery plug assembly.
|
|
(b) Disconnect the HV battery junction block assembly connector.
NOTICE:
Insulate the disconnected connectors with insulating tape.
|
|
(c) Disengage the clamp.
(d) Disengage the 2 claws and open the wiring harness protector.
|
|
(e) Disconnect the HV battery junction block assembly connector.
NOTICE:
Insulate the disconnected connectors with insulating tape.
|
|
(f) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.
|
|
(g) Disconnect the HV battery junction block assembly connector.
|
|
(h) Remove the 4 nuts and HV battery junction block assembly from the No. 1 hybrid battery shield sub-assembly.
NOTICE:
If the HV battery junction block assembly has been struck or dropped, replace it with a new one.
|
|
|