| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001G8ZS |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 09/2022] |
| Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (for HV Model): C13A1; Short circuit in Power source circuit; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] | ||
|
DTC |
C13A1 |
Short circuit in Power source circuit |
DESCRIPTION
C13A1 is stored if the power supply relay in the parking brake ECU assembly has a short circuit.
C13A1 is stored if the power switch is off and a voltage of 2.5 V or higher is applied to the IG terminal and an electric parking brake switch assembly malfunction or wire harness malfunction between the switch and ECU occurs.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
Note |
|---|---|---|---|---|---|
|
C13A1 |
Short circuit in Power source circuit |
Both of following conditions are met:
|
|
DTC stored |
An electric parking brake system malfunction is displayed on the multi-information display. |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.
- After replacing the parking brake ECU (brake actuator assembly), the parking brake indicator light (red) blinks when the power switch is turned on (IG) for the first time. To turn off the parking brake indicator light (red) after replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch to the lock side then to the release side.
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (BEPB CIRCUIT) |
(a) Turn the power switch off.
(b) Disconnect the A113 parking brake ECU (brake actuator assembly) connector.
|
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - IG POWER SOURCE CIRCUIT) |
(a) Turn the power switch off.
(b) Disconnect the A113 parking brake ECU (brake actuator assembly) connector.
|
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
Result:
|
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) |
(a) Remove the electric parking brake switch (electric parking brake switch assembly).
Click here
![2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; PARKING BRAKE: ELECTRIC PARKING BRAKE SWITCH: REMOVAL](/t3Portal/stylegraphics/info.gif)
(b) Inspect the electric parking brake switch (electric parking brake switch assembly).
Click here
| NG |
|
REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) |
|
|
4. |
CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)) |
(a) Disconnect the I41 electric parking brake switch (electric parking brake switch assembly) connector.
(b) Disconnect the A113 parking brake ECU (brake actuator assembly) connector.
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
Result:
|
|
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|