Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001G79K
Model Year Start: 2020 Model: Corolla Prod Date Range: [01/2019 - 09/2022]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): DATA LIST / ACTIVE TEST; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the power switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

(g) According to the display on the Techstream, read the Data List.

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS warning light

ON or OFF

ON: Warning light on

OFF: Warning light off

-

Brake Warning Light

Brake warning light / red (malfunction)

ON or OFF

ON: Warning light on

OFF: Warning light off

-

ECB Warning Light

Brake warning light / yellow (minor malfunction)

ON or OFF

ON: Warning light on

OFF: Warning light off

ECB: Electronically Controlled Brake System

Buzzer

Meter buzzer

ON or OFF

ON: Buzzer on

OFF: Buzzer off

-

Stop Light SW

Stop light switch assembly

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Parking Brake SW

Parking brake switch assembly

ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

TRC(TRAC)/VSC OFF SW

VSC OFF switch (Combination switch assembly)

ON or OFF

ON: Switch on

OFF: Switch off

-

Reservoir Warning SW

Brake fluid level warning switch

ON or OFF

ON: Reservoir level low

OFF: Reservoir level normal

-

Main Idle SW

Main idle switch

ON or OFF

ON: Accelerator pedal released

OFF: Accelerator pedal depressed

-

Shift Lever Position

Shift position information

Fail, 1st, 2nd, 3rd, 4th, 5th, 6th/B, D/M, P,N or R

Actual shift position

-

Inspection Mode

Inspection mode

Other or Inspect

Other: Normal mode

Inspect: Inspection mode

-

Stroke Sensor

Brake pedal stroke sensor

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 0.65 to 1.35 V

Reading increases when brake pedal is depressed

Voltage of Stroke Sensor

Voltage of brake pedal stroke sensor

Min.: -2.50 V, Max.: 2.49 V

-

-

Stroke Sensor2

Brake pedal stroke sensor 2

Min.: 0.00 V, Max.: 5.00 V

Brake pedal released: 3.65 to 4.35 V

Reading decreases when brake pedal is depressed

Voltage of Stroke Sensor2

Voltage of brake pedal stroke sensor 2

Min.: -2.50 V, Max.: 2.49 V

-

-

Deceleration Sensor

Acceleration sensor 1

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Deceleration Sensor2

Acceleration sensor 2

Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

During deceleration/acceleration: Changes continuously

Zero Point of Decele2

Memorized zero value

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Yaw Rate Sensor

Yaw rate sensor 1

Min.: -128 degrees/s, Max.: 127 degrees/s

Vehicle stationary: 0 degrees/s

Turning right: -128 to 0 degrees/s

Turning left: 0 to 127 degrees/s

-

Zero Point of Yaw Rate

Memorized zero value

Min.: -128 degrees, Max.: 127 degrees

-

After completing zero point calibration: 0 degrees

Yaw Rate Sensor2

Yaw rate sensor 2

Min.: -128 degrees/s, Max.: 127 degrees/s

Vehicle stationary: 0 degrees/s

Turning right: -128 to 0 degrees/s

Turning left: 0 to 127 degrees/s

-

Steering Angle Sensor

Steering angle sensor

Min.: -3276.8 degrees, Max.: 3276.7 degrees

Turning left: Increases

Turning right: Decreases

-

Zero Point of Steering Angle

Memorized zero value

Min.: -3276.8 degrees, Max.: 3276.7 degrees

-

After clearing zero point calibration: 0 degrees

Lateral G

Lateral G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During turning: Changes in proportion with lateral acceleration

Forward and Rearward G

Forward and backward G

Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

During acceleration/deceleration: Changes in proportion with acceleration

Yaw Rate Value

Yaw rate value

Min.: -128 degrees/s, Max.: 127 degrees/s

-

During turning: Changes in proportion with yaw

Steering Angle Value

Steering angle value

Min.: -3276.8 degrees, Max.: 3276.7 degrees

-

During steering operation: Changes in proportion with steering wheel rotation

Stop Light Relay

Stop light control relay (Stop light switch assembly)

(STP2 terminal input)

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Slip Indicator Light

Slip indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

FR Wheel Speed

Front speed sensor RH

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FL Wheel Speed

Front speed sensor LH

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RR Wheel Speed

Rear speed sensor RH

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear speed sensor LH

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

Vehicle Speed

Maximum wheel speed sensor

Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph)

Vehicle stopped: 0 km/h (0 mph)

When driving at constant speed: No large fluctuations

FR Wheel Acceleration

Front wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

FL Wheel Acceleration

Front wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RR Wheel Acceleration

Rear wheel RH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

RL Wheel Acceleration

Rear wheel LH acceleration

Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

During deceleration/acceleration: Changes continuously

Stop Light Relay Output

Stop light control relay (Stop light switch assembly)

(STPO terminal output)

ON or OFF

ON: Relay output on

OFF: Relay output off

-

FR Wheel ABS Ctrl Status

Front wheel RH ABS control status

ON or OFF

ON: During control

-

FL Wheel ABS Ctrl Status

Front wheel LH ABS control status

ON or OFF

ON: During control

-

RR Wheel ABS Ctrl Status

Rear wheel RH ABS control status

ON or OFF

ON: During control

-

RL Wheel ABS Ctrl Status

Rear wheel LH ABS control status

ON or OFF

ON: During control

-

BA Ctrl Status

BA control status

ON or OFF

ON: During control

-

PBA Ctrl Status

PBA control status

ON or OFF

ON: During control

-

TRC(TRAC) Ctrl Status

TR(A)C control status

ON or OFF

ON: During control

-

TRC(TRAC) Engine Ctrl Status

TR(A)C engine control status

ON or OFF

ON: During control

-

TRC(TRAC) Brake Ctrl Status

TR(A)C brake control status

ON or OFF

ON: During control

-

FR Wheel VSC Ctrl Status

Front wheel RH VSC control status

ON or OFF

ON: During control

-

FL Wheel VSC Ctrl Status

Front wheel LH VSC control status

ON or OFF

ON: During control

-

RR Wheel VSC Ctrl Status

Rear wheel RH VSC control status

ON or OFF

ON: During control

-

RL Wheel VSC Ctrl Status

Rear wheel LH VSC control status

ON or OFF

ON: During control

-

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle

Min.: 0.0%, Max.: 127.5%

Accelerator pedal released: 0.0%

During accelerator pedal operation: Changes in proportion with the pedal movement

Regenerative Cooperation

Regenerative cooperation

ON or OFF

ON: Operating

OFF: Not operating

-

FR Regenerative Request

FR regenerative request torque

Min.: 0 Nm, Max.: 1048560 Nm

-

Changes according to brake pedal force

(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)

FR Regenerative Operation

FR regenerative operation torque

Min.: 0 Nm, Max.: 1048560 Nm

-

Changes according to brake pedal force

(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)

Solenoid Relay

ABS solenoid relay operation request

ON or OFF

ON: Power switch on (IG) (During initial check)

OFF: Power switch off

-

ECB Motor Relay

Motor relay 1 operation request

ON or OFF

ON: Relay on

OFF: Relay off

ECB: Electronically Controlled Brake System

ECB Motor Relay2

Motor relay 2 operation request

ON or OFF

ON: Relay on

OFF: Relay off

ECB: Electronically Controlled Brake System

ECB Main Relay

Main relay operation request

ON or OFF

ON: Relay on

OFF: Relay off

ECB: Electronically Controlled Brake System

ABS Solenoid (SFRH)

Holding solenoid valve (FRH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRR)

Reduction solenoid valve (FRR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLH)

Holding solenoid valve (FLH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLR)

Reduction solenoid valve (FLR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRH)

Holding solenoid valve (RRH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRR)

Reduction solenoid valve (RRR)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLH)

Holding solenoid valve (RLH)

ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLR)

Reduction solenoid valve (RLR)

ON or OFF

ON: Operating

OFF: Not operating

-

FR Speed Open

Front speed sensor RH open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

FL Speed Open

Front speed sensor LH open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

RR Speed Open

Rear speed sensor RH open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

RL Speed Open

Rear speed sensor LH open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Yaw Rate Open

Yaw rate sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Deceleration Open

Acceleration sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Steering Open

Steering angle sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Stroke Open

Brake pedal stroke sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Stroke2 Open

Brake pedal stroke sensor 2 open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Accumulator Open

Accumulator pressure sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

HV Communication Open

Hybrid vehicle communication open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

VCM1 Voltage Value

VCM1 voltage value

Min.: 0.00 V, Max.: 10.00 V

6.29 to 7.64 V

-

VCM2 Voltage Value

VCM2 voltage value

Min.: 0.00 V, Max.: 10.00 V

6.29 to 7.64 V

-

IG1 Voltage Value

IG1 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

IG2 Voltage Value

IG2 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

BS1 Voltage Value

BS1 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

BS2 Voltage Value

BS2 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

VM1 Voltage Value

VM1 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

VM2 Voltage Value

VM2 voltage value

Min.: 0.00 V, Max.: 20.00 V

-

Changes in proportion to auxiliary battery voltage

MT Voltage Value

MT voltage value

Min.: 0.00 V, Max.: 20.00 V

Pump motor off: 0.00 V

Pump motor on: 12.00 V

-

BH Standby Light

Brake hold standby indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

BH Operated Light

Brake hold operated indicator light

ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

TRAC/VSC Off Mode

TR(A)C/VSC off mode

Normal, TRC OFF, VSC Expert Mode or VSC OFF

Normal: Normal mode

TRC OFF: TR(A)C off mode

VSC Expert Mode: VSC expert mode

VSC OFF: VSC off mode

-

Number of DTC

Number of DTC

Min.: 0, Max.: 255

-

Number of DTCs output is displayed

FR Speed Sensor Voltage Open

Front speed sensor RH voltage open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

FL Speed Sensor Voltage Open

Front speed sensor LH voltage open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

RR Speed Sensor Voltage Open

Rear speed sensor RH voltage open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

RL Speed Sensor Voltage Open

Rear speed sensor LH voltage open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Yaw Rate Sensor Voltage Open

Yaw rate sensor voltage open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

SLA Solenoid Current

Linear solenoid addition valve (SLA) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 to 1.50 A

-

SLR Solenoid Current

Linear solenoid reduction valve (SLR) current

Min.: 0.00 A, Max.: 3.00 A

Brake pedal released: 0.00 to 1.50 A

-

Brake Hold Switch

Brake hold switch (Electric parking brake switch assembly)

ON or OFF

ON: Switch on

OFF: Switch off

-

Reaction Force Pressure

Pressure value of stroke simulator

Min.: 0.00 MPa, Max.: 24.48 MPa

Brake pedal released: 0.00 MPa

Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal

Servo Pressure

Pressure value of servo

Min.: 0.00 MPa, Max.: 24.48 MPa

Brake pedal released: 0.00 to 2.10 MPa

Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal

Accumulator Pressure

Accumulator pressure output value

Min.: 0.00 MPa, Max.: 24.48 MPa

15.00 to 21.00 MPa

(Pressure stable and pump motor stopped)

When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator

Reaction Force Pressure Sensor Temperature

Reaction force pressure sensor temperature

Min.: -80°C (-112°F), Max.: 175°C (347°F)

-30°C (-22°F) to 100°C (212°F)

-

Servo Pressure Sensor Temperature

Servo pressure sensor temperature

Min.: -80°C (-112°F), Max.: 175°C (347°F)

-30°C (-22°F) to 100°C (212°F)

-

Accumulator Pressure Sensor Temperature

Accumulator pressure sensor temperature

Min.: -80°C (-112°F), Max.: 175°C (347°F)

-30°C (-22°F) to 100°C (212°F)

-

MT Voltage Value (ABS)

ABS motor voltage value

Min.: 0.00 V, Max.: 20.00 V

ABS motor off: 0.00 V

ABS motor on: 11.00 to 14.00 V

-

ECB Solenoid (SGH)

Switching solenoid valve (SGH)

ON or OFF

ON: Solenoid on

OFF: Solenoid off

ECB: Electronically Controlled Brake System

ECB Solenoid (SSA)

Switching solenoid valve (SSA)

ON or OFF

ON: Solenoid on

OFF: Solenoid off

ECB: Electronically Controlled Brake System

Power Supply Voltage Low Light ON Trip Counter

Number of trips after light illuminated when power supply voltage was low

Min.: 0, Max.: 255

-

-

SGH Solenoid Current

Switching solenoid valve (SGH) current

Min.: 0.00 A, Max.: 3.00 A

0.00 to 1.50 A

-

SSA Solenoid Current

Switching solenoid valve (SSA) current

Min.: 0.00 A, Max.: 3.00 A

0.00 to 1.50 A

-

Reaction Force Pressure Sensor Open

Reaction force pressure sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Servo Pressure Sensor Open

Servo pressure sensor open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

Ambient Temperature

Ambient temperature

Min.: -128°C (-198.4°F), Max.: 127°C (260.6°F)

-30°C (-22°F) to 100°C (212°F)

Changes according to ambient temperature

Air Bag ECU Communication Open

Airbag sensor assembly communication open detection

Error or Normal

Error: Momentary interruption

Normal: Normal

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the power switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the power switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

ABS Warning Light

ABS warning light

Warning light ON/OFF

Observe combination meter assembly

Brake Warning Light

Brake warning light / red (malfunction)

Warning light ON/OFF

Observe combination meter assembly

ECB Warning Light

Brake warning light / yellow (minor malfunction)

Warning light ON/OFF

  • Observe combination meter assembly
  • ECB: Electronically Controlled Brake System

Buzzer

Meter buzzer

Buzzer ON/OFF

Buzzer can be heard

Solenoid Relay

Solenoid relay

Relay ON/OFF

-

Motor Relay

ABS motor relay

Relay ON/OFF

Operating sound of motor can be heard.

Stop Light Relay

Stop light control relay (Stop light switch assembly)

Relay ON/OFF

-

ECB Main Relay

Main relay

Relay ON/OFF

ECB: Electronically Controlled Brake System

ABS Solenoid (SRLR)

Reduction solenoid valve (RLR)

Solenoid ON/OFF

-

ABS Solenoid (SRLH)

Holding solenoid valve (RLH)

Solenoid ON/OFF

-

ABS Solenoid (SRRR)

Reduction solenoid valve (RRR)

Solenoid ON/OFF

-

ABS Solenoid (SRRH)

Holding solenoid valve (RRH)

Solenoid ON/OFF

-

ABS Solenoid (SFLR)

Reduction solenoid valve (FLR)

Solenoid ON/OFF

-

ABS Solenoid (SFLH)

Holding solenoid valve (FLH)

Solenoid ON/OFF

-

ABS Solenoid (SFRR)

Reduction solenoid valve (FRR)

Solenoid ON/OFF

-

ABS Solenoid (SFRH)

Holding solenoid valve (FRH)

Solenoid ON/OFF

-

ECB Control Invalid

Electronically controlled brake system control invalid

Control invalid ON/OFF

  • Electronically controlled brake system control is disabled (braking with no accumulator assist)
  • ECB: Electronically Controlled Brake System

Accumulator Zero Down

Reduction of pressure in accumulator

Activation ON/OFF

Brake fluid in the accumulator makes noise

Actuator Air Bleeding Pattern

Actuator air bleeding pattern activation

Activation ON/OFF

When accumulator pressure drops, pump operation creates sound

BH Standby Light

Brake hold standby indicator light

Indicator light ON/OFF

Observe combination meter assembly

BH Operated Light

Brake hold operated indicator light

Indicator light ON/OFF

Observe combination meter assembly

TRC(TRAC) OFF Indicator Light

Multi-information display (Traction Control Turned Off)

Display ON/OFF

Observe combination meter assembly

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light ON/OFF

Observe combination meter assembly

Slip Indicator Light

Slip indicator light

Indicator light ON/OFF

Observe combination meter assembly

EBS Relay

Emergency brake signal operation

Operation ON/OFF

w/ Emergency Brake Signal

ECB Solenoid (SLR)

Linear solenoid reduction valve (SLR)

Solenoid ON/OFF

ECB: Electronically Controlled Brake System

ECB Solenoid (SLA)

Linear solenoid addition valve (SLA)

Solenoid ON/OFF

ECB: Electronically Controlled Brake System

ECB Solenoid (SSA)

Switching solenoid valve (SSA)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ECB Solenoid (SGH)

Switching solenoid valve (SGH)

Solenoid ON/OFF

  • Operation sound of solenoid (clicking sound) can be heard
  • ECB: Electronically Controlled Brake System

ABS Solenoid

Solenoid valve (FRH, FRR, FLH, FLR, RRH, RRR, RLH or RLR)

Solenoid SFRH/SFRR/SFLH/ SFLR/SRRH/SRRR/SRLH/SRLR

Operation sound of solenoid (clicking sound) can be heard