Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G706 |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for HV Model): B150013; Fuel Sender Circuit Open; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] |
DTC
|
B150013
|
Fuel Sender Circuit Open
|
DESCRIPTION
This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B150013
|
Fuel Sender Circuit Open
|
Diagnosis Condition:
-
The power switch is on (IG)
-
IG power source voltage is 9.5 V or more
Malfunction Status:
-
Voltage signal from fuel sender gauge assembly is 0.2 V or less
-
Voltage signal from fuel sender gauge assembly is 4.7 V or more
Malfunction Time:
|
-
Harness or connector
-
Fuel sender gauge assembly
-
Fuel suction tube with pump and gauge assembly
-
Combination meter assembly
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Fuel Input
|
Fuel input
|
Min.: 0.00 L, Max.: 655.35 L or Unset
|
-
Fuel receiver gauge indicates F: 38.30 L
-
Fuel receiver gauge indicates 3/4: 29.78 L
-
Fuel receiver gauge indicates 1/2: 21.30 L
-
Fuel receiver gauge indicates 1/4: 12.77 L
-
Fuel receiver gauge indicates E: 4.25 L
|
-
|
Body Electrical > Combination Meter > Data List
Tester Display
|
Fuel Input
|
Result
|
Proceed to
|
Fuel level data can be displayed on the Techstream
|
A
|
Fuel level data cannot be displayed on the Techstream
|
B
|
B
|
|
|
2.
|
INSPECT FUEL SENDER GAUGE ASSEMBLY
|
(a) Remove the fuel sender gauge assembly.
w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
(b) Inspect the fuel sender gauge assembly.
w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
NG |
|
REPLACE FUEL SENDER GAUGE ASSEMBLY
w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
OK
|
|
|
3.
|
INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
|
*a
|
Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
O44-1 (FV) - A-3
|
Always
|
Below 1 Ω
|
O44-2 (FE) - A-2
|
Always
|
Below 1 Ω
|
O44-3 (FS) - A-1
|
Always
|
Below 1 Ω
|
O44-1 (FV) - O44-3 (FS)
or
A-3 - A-1
|
Always
|
10 kΩ or higher
|
O44-1 (FV) - O44-2 (FE)
or
A-3 - A-2
|
Always
|
10 kΩ or higher
|
O44-2 (FE) - O44-3 (FS)
or
A-2 - A-1
|
Always
|
10 kΩ or higher
|
NG |
|
REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
w/ Canister Pump Module: Click here
w/o Canister Pump Module: Click here
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
|
(a) Disconnect the I4 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
O44-1 (FV) - I4-14 (FV)
|
Always
|
Below 1 Ω
|
O44-3 (FS) - I4-31 (FR)
|
Always
|
Below 1 Ω
|
O44-2 (FE) - I4-24 (FE&B)
|
Always
|
Below 1 Ω
|
O44-1 (FV) or I4-14 (FV) - Body ground
|
Always
|
10 kΩ or higher
|
O44-3 (FS) or I4-31 (FR) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|