Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001G5RZ
Model Year Start: 2020 Model: GR Corolla Prod Date Range: [01/2019 - 09/2019]
Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: B15C3; Speaker Output Short; 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2019]

DTC

B15C3

Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15C3

Speaker Output Short

A short is detected in the speaker output circuit

  • Harness or connector
  • Speaker
  • DCM (telematics transceiver)*3
  • Stereo Component Amplifier*1
  • Radio and Display Receiver Assembly*2
  • *1: w/ Stereo Component Amplifier Assembly
  • *2: w/o Stereo Component Amplifier Assembly
  • *3: w/ Manual (SOS) Switch

WIRING DIAGRAM

w/o Stereo Component Amplifier Assembly
w/ Stereo Component Amplifier Assembly (for Hatchback Model)
w/ Stereo Component Amplifier Assembly (for Sedan Model)

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.
  • Before replacing the DCM (telematics transceiver), refer to Registration.

    Click here 2020 MY Corolla Corolla Hatchback GR Corolla [01/2019 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

PROCEDURE

1.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/o Stereo Component Amplifier Assembly

A

w/ Stereo Component Amplifier Assembly

B

B

GO TO STEP 15

A

2.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/o Manual (SOS) Switch

A

w/ Manual (SOS) Switch

B

B

GO TO STEP 8

A

3.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, SPEAKERS - BODY GROUND)

(a) Disconnect the I71 radio and display receiver assembly connector.

(b) Disconnect the I77 and I76 front No. 2 speaker assembly connector.

(c) Disconnect the M4 and N4 rear speaker assembly connectors.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I71-1 (FR+) or I76-4 (TWR+) - Body ground

Always

10 kΩ or higher

I71-6 (FR-) or I76-2 (TWR-) - Body ground

Always

10 kΩ or higher

I71-2 (FL+) or I77-4 (TWL+) - Body ground

Always

10 kΩ or higher

I71-7 (FL-) or I77-2 (TWL-) - Body ground

Always

10 kΩ or higher

I71-4 (RR+) or M4-2 - Body ground

Always

10 kΩ or higher

I71-9 (RR-) or M4-1 - Body ground

Always

10 kΩ or higher

I71-3 (RL+) or N4-2 - Body ground

Always

10 kΩ or higher

I71-8 (RL-) or N4-1 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.

(b) Disconnect the I76 and I77 front No. 2 speaker assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-2 or I76-3 (+) - Body ground

Always

10 kΩ or higher

K1-1 or I76-1 (-) - Body ground

Always

10 kΩ or higher

L1-2 or I77-3 (+) - Body ground

Always

10 kΩ or higher

L1-1 or I77-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

6.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

NG

REPLACE REAR SPEAKER ASSEMBLY

OK

7.

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Inspect the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: INSPECTION

(c) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

8.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND)

(a) Disconnect the I71 radio and display receiver assembly connector.

(b) Disconnect the I72 DCM (telematics transceiver) connector.

(c) Disconnect the I77 front No. 2 speaker assembly LH connector.

(d) Disconnect the M4 and N4 rear speaker assembly connectors.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I71-1 (FR+) or I72-2 (SPI+) - Body ground

Always

10 kΩ or higher

I71-6 (FR-) or I72-3 (SPI-) - Body ground

Always

10 kΩ or higher

I71-2 (FL+) or I77-4 (TWL+) - Body ground

Always

10 kΩ or higher

I71-7 (FL-) or I77-2 (TWL-) - Body ground

Always

10 kΩ or higher

I71-4 (RR+) or M4-2 - Body ground

Always

10 kΩ or higher

I71-9 (RR-) or M4-1 - Body ground

Always

10 kΩ or higher

I71-3 (RL+) or N4-2 - Body ground

Always

10 kΩ or higher

I71-8 (RL-) or N4-1 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

9.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND)

(a) Disconnect the I72 DCM (telematics transceiver) connector.

(b) Disconnect the I76 front No. 2 speaker assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I72-5 (SPO+) or I76-4 (TWR+) - Body ground

Always

10 kΩ or higher

I72-6 (SPO-) or I76-2 (TWR-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Remove the DCM (telematics transceiver).

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2019]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (SPI+) - 5 (SPO+)

Always

Below 1 Ω

3 (SPI-) - 6 (SPO-)

Always

Below 1 Ω

2 (SPI+) - 3 (SPI-)

Always

10 kΩ or higher

5 (SPO+) - 6 (SPO-)

Always

10 kΩ or higher

2 (SPI+) or 5 (SPO+) - Body ground

Always

10 kΩ or higher

3 (SPI-) or 6 (SPO-) - Body ground

Always

10 kΩ or higher

*a

Component without harness connected

(DCM (Telematics Transceiver))

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

OK

11.

CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.

(b) Disconnect the I76 and I77 front No. 2 speaker assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-2 or I76-3 (+) - Body ground

Always

10 kΩ or higher

K1-1 or I76-1 (-) - Body ground

Always

10 kΩ or higher

L1-2 or I77-3 (+) - Body ground

Always

10 kΩ or higher

L1-1 or I77-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

12.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

13.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

NG

REPLACE REAR SPEAKER ASSEMBLY

OK

14.

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Inspect the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: INSPECTION

(c) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

15.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for Hatchback Model

A

for Sedan Model (w/ Manual (SOS) Switch)

B

for Sedan Model (w/o Manual (SOS) Switch)

C

B

GO TO STEP 24

C

GO TO STEP 27

A

16.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND)

(a) Disconnect the I54 stereo component amplifier assembly connector.

(b) Disconnect the I72 DCM (telematics transceiver) connector.

(c) Disconnect the I7 front No. 2 speaker assembly LH connector.

(d) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.

(e) Disconnect the M4 and N4 rear speaker assembly connectors.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I54-15 (FR+) or I74-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-30 (FR-) or I74-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-13 (FL+) or I75-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-28 (FL-) or I75-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-14 (TWR+) or I72-2 (SPI+) - Body ground

Always

10 kΩ or higher

I54-29 (TWR-) or I72-3 (SPI-) - Body ground

Always

10 kΩ or higher

I54-12 (TWL+) or I7-2 - Body ground

Always

10 kΩ or higher

I54-27 (TWL-) or I7-1 - Body ground

Always

10 kΩ or higher

I54-11 (RR+) or M4-2 - Body ground

Always

10 kΩ or higher

I54-26 (RR-) or M4-1 - Body ground

Always

10 kΩ or higher

I54-9 (RL+) or N4-2 - Body ground

Always

10 kΩ or higher

I54-24 (RL-) or N4-1 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

17.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND)

(a) Disconnect the I72 DCM (telematics transceiver) connector.

(b) Disconnect the I6 front No. 2 speaker assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I72-5 (SPO+) or I6-2 - Body ground

Always

10 kΩ or higher

I72-6 (SPO-) or I6-1 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

18.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Remove the DCM (telematics transceiver).

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2019]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (SPI+) - 5 (SPO+)

Always

Below 1 Ω

3 (SPI-) - 6 (SPO-)

Always

Below 1 Ω

2 (SPI+) - 3 (SPI-)

Always

10 kΩ or higher

5 (SPO+) - 6 (SPO-)

Always

10 kΩ or higher

2 (SPI+) or 5 (SPO+) - Body ground

Always

10 kΩ or higher

3 (SPI-) or 6 (SPO-) - Body ground

Always

10 kΩ or higher

*a

Component without harness connected

(DCM (Telematics Transceiver))

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

OK

19.

CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 3 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.

(b) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-2 or I74-3 (+) - Body ground

Always

10 kΩ or higher

K1-1 or I74-1 (-) - Body ground

Always

10 kΩ or higher

L1-2 or I75-3 (+) - Body ground

Always

10 kΩ or higher

L1-1 or I75-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

20.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

21.

INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Inspect the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

OK

22.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

NG

REPLACE REAR SPEAKER ASSEMBLY

OK

23.

REPLACE FRONT NO. 3 SPEAKER ASSEMBLY

(a) Remove the front No. 3 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: REMOVAL

(b) Inspect the front No. 3 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: INSPECTION

(c) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; AUDIO / VIDEO: STEREO COMPONENT AMPLIFIER: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: STEREO COMPONENT AMPLIFIER: REMOVAL

24.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND)

(a) Disconnect the I54 stereo component amplifier assembly connector.

(b) Disconnect the I72 DCM (telematics transceiver) connector.

(c) Disconnect the I7 front No. 2 speaker assembly LH connector.

(d) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.

(e) Disconnect the M4 and N4 rear speaker assembly connectors.

(f) Disconnect the O71 rear No. 2 speaker assembly connector.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I54-14 (TWR+) or I72-2 (SPI+) - Body ground

Always

10 kΩ or higher

I54-29 (TWR-) or I72-3 (SPI-) - Body ground

Always

10 kΩ or higher

I54-12 (TWL+) or I7-2 (TWL+) - Body ground

Always

10 kΩ or higher

I54-27 (TWL-) or I7-1 (TWL-) - Body ground

Always

10 kΩ or higher

I54-15 (FR+) or I74-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-30 (FR-) or I74-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-13 (FL+) or I75-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-28 (FL-) or I75-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-11 (RR+) or M4-2 - Body ground

Always

10 kΩ or higher

154-26 (RR-) or M4-1 - Body ground

Always

10 kΩ or higher

I54-9 (RL+) or N4-2 - Body ground

Always

10 kΩ or higher

I54-24 (RL-) or N4-1 - Body ground

Always

10 kΩ or higher

I54-10 (WF1+) or O71-4 (WF1+) - Body ground

Always

10 kΩ or higher

I54-25 (WF1-) or O71-3 (WF1-) - Body ground

Always

10 kΩ or higher

I54-8 (WF2+) or O71-2 (WF2+) - Body ground

Always

10 kΩ or higher

I54-23 (WF2-) or O71-1 (WF2-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

25.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND)

(a) Disconnect the I72 DCM (telematics transceiver) connector.

(b) Disconnect the I6 front No. 2 speaker assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I72-5 (SPO+) or I6-2 - Body ground

Always

10 kΩ or higher

I72-6 (SPO-) or I6-1 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

26.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Remove the DCM (telematics transceiver).

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 09/2019]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (SPI+) - 5 (SPO+)

Always

Below 1 Ω

3 (SPI-) - 6 (SPO-)

Always

Below 1 Ω

2 (SPI+) - 3 (SPI-)

Always

10 kΩ or higher

5 (SPO+) - 6 (SPO-)

Always

10 kΩ or higher

2 (SPI+) or 5 (SPO+) - Body ground

Always

10 kΩ or higher

3 (SPI-) or 6 (SPO-) - Body ground

Always

10 kΩ or higher

*a

Component without harness connected

(DCM (Telematics Transceiver))

OK

GO TO STEP 28

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

27.

CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY OR SPEAKERS - BODY GROUND)

(a) Disconnect the I54 stereo component amplifier assembly connector.

(b) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.

(c) Disconnect the I6 and I7 front No. 2 speaker assembly connectors.

(d) Disconnect the M4 and N4 rear speaker assembly connectors.

(e) Disconnect the O71 rear No. 2 speaker assembly connector.

(f) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I54-15 (FR+) or I74-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-30 (FR-) or I74-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-13 (FL+) or I75-4 (+TW) - Body ground

Always

10 kΩ or higher

I54-28 (FL-) or I75-2 (-TW) - Body ground

Always

10 kΩ or higher

I54-14 (TWR+) or I6-2 - Body ground

Always

10 kΩ or higher

I54-29 (TWR-) or I6-1 - Body ground

Always

10 kΩ or higher

I54-12 (TWL+) or I7-2 - Body ground

Always

10 kΩ or higher

I54-27 (TWL-) or I7-1 - Body ground

Always

10 kΩ or higher

I54-11 (RR+) or M4-2 - Body ground

Always

10 kΩ or higher

I54-26 (RR-) or M4-1 - Body ground

Always

10 kΩ or higher

I54-9 (RL+) or N4-2 - Body ground

Always

10 kΩ or higher

I54-24 (RL-) or N4-1 - Body ground

Always

10 kΩ or higher

I54-10 (WF1+) or O71-4 (WF1+) - Body ground

Always

10 kΩ or higher

I54-25 (WF1-) or O71-3 (WF1-) - Body ground

Always

10 kΩ or higher

I54-8 (WF2+) or O71-2 (WF2+) - Body ground

Always

10 kΩ or higher

I54-23 (WF2-) or O71-1 (WF2-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

28.

CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 3 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the K1 and L1 front No. 1 speaker assembly connectors.

(b) Disconnect the I74 and I75 front No. 3 speaker assembly connectors.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K1-2 or I74-3 (+) - Body ground

Always

10 kΩ or higher

K1-1 or I74-1 (-) - Body ground

Always

10 kΩ or higher

L1-2 or I75-3 (+) - Body ground

Always

10 kΩ or higher

L1-1 or I75-1 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

29.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL

(b) Inspect the front No. 1 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: FRONT DOOR SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

30.

INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: REMOVAL

(b) Inspect the front No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: INSTRUMENT PANEL SPEAKER: INSPECTION

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

OK

31.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: REMOVAL

(b) Inspect the rear speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: REAR DOOR SPEAKER: INSPECTION

NG

REPLACE REAR SPEAKER ASSEMBLY

OK

32.

INSPECT REAR NO. 2 SPEAKER ASSEMBLY

(a) Remove the rear No. 2 speaker assembly.

Click here 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 04/2020]; AUDIO / VIDEO: REAR PACKAGE TRAY SPEAKER: REMOVAL

(b) Inspect the rear No. 2 speaker assembly.

Click here 2020 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 -        ]; AUDIO / VIDEO: REAR PACKAGE TRAY SPEAKER: INSPECTION

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY

OK

33.

REPLACE FRONT NO. 3 SPEAKER ASSEMBLY

(a) Remove the front No. 3 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: REMOVAL

(b) Inspect the front No. 3 speaker assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; AUDIO / VIDEO: PILLAR SPEAKER: INSPECTION

(c) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(d) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; AUDIO / VIDEO: STEREO COMPONENT AMPLIFIER: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; AUDIO / VIDEO: STEREO COMPONENT AMPLIFIER: REMOVAL