Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G4Q6 |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 09/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): B1825-B1828; Short in Side Squib (LH) Circuit; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] |
DTC
|
B1825
|
Short in Side Squib (LH) Circuit
|
DTC
|
B1826
|
Open in Side Squib (LH) Circuit
|
DTC
|
B1827
|
Short in Side Squib (LH) Circuit (to Ground)
|
DTC
|
B1828
|
Short in Side Squib (LH) Circuit (to +B)
|
DESCRIPTION
The front side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front side squib LH circuit.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Warning Indicate
|
Test Mode / Check Mode
|
B1825
|
Short in Side Squib (LH) Circuit
|
-
The airbag sensor assembly detects a line short in the front side squib LH circuit during the primary check.
-
Front side squib LH malfunction
-
Airbag sensor assembly malfunction
|
-
Floor wire
-
Front side squib LH (Front seat airbag assembly LH)
-
Airbag sensor assembly
|
Comes on
|
Applies to check mode
|
B1826
|
Open in Side Squib (LH) Circuit
|
-
The airbag sensor assembly detects an open in the front side squib LH circuit.
-
Front side squib LH malfunction
-
Airbag sensor assembly malfunction
|
-
Floor wire
-
Front side squib LH (Front seat airbag assembly LH)
-
Airbag sensor assembly
|
Comes on
|
Applies to check mode
|
B1827
|
Short in Side Squib (LH) Circuit (to Ground)
|
-
The airbag sensor assembly detects a short to ground in the front side squib LH circuit.
-
Front side squib LH malfunction
-
Airbag sensor assembly malfunction
|
-
Floor wire
-
Front side squib LH (Front seat airbag assembly LH)
-
Airbag sensor assembly
|
Comes on
|
Applies to check mode
|
B1828
|
Short in Side Squib (LH) Circuit (to +B)
|
-
The airbag sensor assembly detects a short to B+ in the front side squib LH circuit.
-
Front side squib LH malfunction
-
Airbag sensor assembly malfunction
|
-
Floor wire
-
Front side squib LH (Front seat airbag assembly LH)
-
Airbag sensor assembly
|
Comes on
|
Applies to check mode
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
HINT:
-
Perform the simulation method by selecting check mode (Signal Check) using the Techstream.
Click here
-
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click here
PROCEDURE
(a) Turn the power switch off.
|
|
*1
|
Front Seat Airbag Assembly LH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Floor Wire
|
|
|
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.
OK:
The connectors are properly connected.
HINT:
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
(d) Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.
(e) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
(f) Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.
OK:
The short springs are not deformed or damaged.
NG |
|
REPLACE FLOOR WIRE
|
OK
|
|
|
2.
|
CHECK FRONT SEAT AIRBAG ASSEMBLY LH
|
(a) Connect the connector to the airbag sensor assembly.
|
|
*1
|
Front Seat Airbag Assembly LH
|
*2
|
Airbag Sensor Assembly
|
*a
|
Front view of wire harness connector
(to Front Seat Airbag Assembly LH)
|
|
|
(b) Connect SST (resistance 2.1 Ω) to connector C.
CAUTION:
Never connect a tester to the front seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
-
Do not forcibly insert SST into the terminals of the connector when connecting it.
-
Insert SST straight into the terminals of the connector.
SST: 09843-18061
(c) Connect the cable to the negative (-) auxiliary battery terminal.
(d) Turn the power switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(f) Turn the power switch off.
(g) Turn the power switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1825, B1826, B1827 or B1828 is not output.
HINT:
Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.
(i) Turn the power switch off.
(j) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(k) Disconnect SST from connector C.
NG
|
|
|
(a) Disconnect the floor wire from the airbag sensor assembly.
|
|
*1
|
Front Seat Airbag Assembly LH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Floor Wire
|
*a
|
Front view of wire harness connector
(to Front Seat Airbag Assembly LH)
|
|
|
(b) Check for a short to B+ in the circuit.
(1) Connect the cable to the negative (-) auxiliary battery terminal.
(2) Turn the power switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
Oe1-1 (SFL+) - Body ground
|
Power switch on (IG)
|
Below 1 V
|
Oe1-2 (SFL-) - Body ground
|
Power switch on (IG)
|
Below 1 V
|
(4) Turn the power switch off.
(5) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check for an open in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Oe1-1 (SFL+) - Oe1-2 (SFL-)
|
Always
|
Below 1 Ω
|
(d) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Oe1-1 (SFL+) - Body ground
|
Always
|
1 MΩ or higher
|
Oe1-2 (SFL-) - Body ground
|
Always
|
1 MΩ or higher
|
(e) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B.
Click here
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Oe1-1 (SFL+) - Oe1-2 (SFL-)
|
Always
|
1 MΩ or higher
|
(3) Restore the released activation prevention mechanism of connector B to the original condition.
NG |
|
REPLACE FLOOR WIRE
|
OK
|
|
|
(a) Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.
|
|
*1
|
Front Seat Airbag Assembly LH
|
*2
|
Airbag Sensor Assembly
|
|
|
(b) Connect the cable to the negative (-) auxiliary battery terminal.
(c) Turn the power switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(e) Turn the power switch off.
(f) Turn the power switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1825, B1826, B1827 or B1828 is not output.
HINT:
Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.
|