| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001G4Q3 |
| Model Year Start: 2020 | Model: Corolla | Prod Date Range: [01/2019 - 09/2022] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for HV Model): B1815-B1818; Short in P Squib (Dual Stage - 2nd Step) Circuit; 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022] | ||
|
DTC |
B1815 |
Short in P Squib (Dual Stage - 2nd Step) Circuit |
|
DTC |
B1816 |
Open in P Squib (Dual Stage - 2nd Step) Circuit |
|
DTC |
B1817 |
Short in P Squib (Dual Stage - 2nd Step) Circuit (to Ground) |
|
DTC |
B1818 |
Short in P Squib (Dual Stage - 2nd Step) Circuit (to +B) |
DESCRIPTION
The front passenger squib 2nd step circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger squib 2nd step circuit.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
Test Mode / Check Mode |
|---|---|---|---|---|---|
|
B1815 |
Short in P Squib (Dual Stage - 2nd Step) Circuit |
|
|
Comes on |
Applies to check mode |
|
B1816 |
Open in P Squib (Dual Stage - 2nd Step) Circuit |
|
|
Comes on |
Applies to check mode |
|
B1817 |
Short in P Squib (Dual Stage - 2nd Step) Circuit (to Ground) |
|
|
Comes on |
Applies to check mode |
|
B1818 |
Short in P Squib (Dual Stage - 2nd Step) Circuit (to +B) |
|
|
Comes on |
Applies to check mode |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
HINT:
-
Perform the simulation method by selecting check mode (Signal Check) using the Techstream.
Click here
-
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click here
PROCEDURE
|
1. |
CHECK CONNECTORS |
|
(a) Turn the power switch off. |
|
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.
OK:
The connectors are properly connected.
HINT:
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
(d) Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.
(e) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
(f) Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not loose, deformed or damaged.
OK:
The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
(g) Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and No. 2 instrument panel wire connector are not deformed or damaged.
OK:
The short springs are not deformed or damaged.
| NG |
|
REPLACE WIRE HARNESS |
|
|
2. |
CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY |
|
(a) Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly. |
|
(b) Connect SST (resistance 2.1 Ω) to connector E (black connector).
CAUTION:
Never connect a tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting it.
- Insert SST straight into the terminals of the connector.
SST: 09843-18061
(c) Connect the cable to the negative (-) auxiliary battery terminal.
(d) Turn the power switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(f) Turn the power switch off.
(g) Turn the power switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1815, B1816, B1817 or B1818 is not output.
HINT:
Codes other than DTCs B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.
(i) Turn the power switch off.
(j) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(k) Disconnect SST from connector E.
| OK |
|
REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
|
|
|
3. |
CHECK FRONT PASSENGER SQUIB 2ND STEP CIRCUIT |
|
(a) Disconnect the instrument panel wire from the airbag sensor assembly. |
|
(b) Check for a short to B+ in the circuit.
(1) Connect the cable to the negative (-) auxiliary battery terminal.
(2) Turn the power switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - Body ground |
Power switch on (IG) |
Below 1 V |
|
g2-1 (P2-) - Body ground |
Power switch on (IG) |
Below 1 V |
(4) Turn the power switch off.
(5) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check for an open in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - g2-1 (P2-) |
Always |
Below 1 Ω |
(d) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - Body ground |
Always |
1 MΩ or higher |
|
g2-1 (P2-) - Body ground |
Always |
1 MΩ or higher |
(e) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B.
Click here
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - g2-1 (P2-) |
Always |
1 MΩ or higher |
(3) Restore the released activation prevention mechanism of connector B to the original condition.
| NG |
|
|
|
4. |
CHECK DTC |
|
(a) Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly. |
|
(b) Connect the cable to the negative (-) auxiliary battery terminal.
(c) Turn the power switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(e) Turn the power switch off.
(f) Turn the power switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1815, B1816, B1817 or B1818 is not output.
HINT:
Codes other than DTCs B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.
| OK |
|
| NG |
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
|
5. |
CHECK INSTRUMENT PANEL WIRE |
|
(a) Disconnect the No. 2 instrument panel wire from the instrument panel wire. |
|
(b) Check for a short to B+ in the circuit.
(1) Connect the cable to the negative (-) auxiliary battery terminal.
(2) Turn the power switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ig2-3 (P2+) - Body ground |
Power switch on (IG) |
Below 1 V |
|
Ig2-4 (P2-) - Body ground |
Power switch on (IG) |
Below 1 V |
(4) Turn the power switch off.
(5) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check for an open in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ig2-3 (P2+) - Ig2-4 (P2-) |
Always |
Below 1 Ω |
(d) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ig2-3 (P2+) - Body ground |
Always |
1 MΩ or higher |
|
Ig2-4 (P2-) - Body ground |
Always |
1 MΩ or higher |
(e) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector B.
Click here
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ig2-3 (P2+) - Ig2-4 (P2-) |
Always |
1 MΩ or higher |
(3) Restore the released activation prevention mechanism of connector B to the original condition.
| NG |
|
REPLACE INSTRUMENT PANEL WIRE |
|
|
6. |
CHECK NO. 2 INSTRUMENT PANEL WIRE |
|
(a) Check for a short to B+ in the circuit. (1) Connect the cable to the negative (-) auxiliary battery terminal. (2) Turn the power switch on (IG). (3) Measure the voltage according to the value(s) in the table below. Standard Voltage:
(4) Turn the power switch off. (5) Disconnect the cable from the negative (-) auxiliary battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system. |
|
(b) Check for an open in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - g2-1 (P2-) |
Always |
Below 1 Ω |
(c) Check for a short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - Body ground |
Always |
1 MΩ or higher |
|
g2-1 (P2-) - Body ground |
Always |
1 MΩ or higher |
(d) Check for a short in the circuit.
(1) Release the activation prevention mechanism built into connector D.
Click here
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
g2-2 (P2+) - g2-1 (P2-) |
Always |
1 MΩ or higher |
(3) Restore the released activation prevention mechanism of connector D to the original condition.
| OK |
|
| NG |
|
REPLACE NO. 2 INSTRUMENT PANEL WIRE |
|
|