Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G46A |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 03/2019] |
Title: 2ZR-FAE (LUBRICATION): OIL PUMP: REMOVAL; 2020 MY Corolla [01/2019 - 03/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
-
Reset memory
-
Deceleration sensor zero point calibration
-
CVT oil pressure calibration
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
|
Replacement of ECM*1
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function
|
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
Engine start
|
|
-
Replacement of throttle body assembly
-
Replacement of engine assembly
-
Replacement of cylinder head sub-assembly
-
Replacement of ignition coil assembly
-
Gas leak from exhaust system is repaired
|
Inspection After Repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
|
Perform headlight ECU sub-assembly LH initialization
|
Lighting system (w/ AFS)(EXT)
|
|
Front wheel alignment adjustment
|
-
Perform "Reset Memory".
-
Perform acceleration sensor zero point calibration and store system information memorization.
|
-
VSC is disabled or malfunctions
-
DTCs are output
-
Slip indicator light illuminates
-
ABS warning light illuminates
|
w/ Electric Parking Brake System:
w/o Electric Parking Brake System:
|
CVT fluid
|
ATF thermal degradation estimate reset
|
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
|
for K313
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Gasoline Model))
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. INSTALL ENGINE TO ENGINE STAND
Click here
2. REMOVE ENGINE HANGERS
Click here
3. REMOVE THROTTLE BODY ASSEMBLY
Click here
4. REMOVE THROTTLE BODY GASKET
Click here
5. REMOVE PURGE VALVE (PURGE VSV)
Click here
6. REMOVE INTAKE MANIFOLD
Click here
7. DISCONNECT FUEL TUBE SUB-ASSEMBLY
Click here
8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
Click here
9. REMOVE NO. 1 DELIVERY PIPE SPACER
Click here
10. REMOVE INJECTOR VIBRATION INSULATOR
Click here
11. REMOVE FUEL INJECTOR ASSEMBLY
Click here
12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Click here
13. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Click here
14. REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Click here
15. REMOVE MANIFOLD STAY
Click here
16. REMOVE EXHAUST MANIFOLD
Click here
17. REMOVE VENTILATION HOSE
Click here
18. DISCONNECT NO. 3 WATER BY-PASS HOSE
Click here
19. REMOVE WATER BY-PASS HOSE
Click here
20. REMOVE WATER INLET HOSE
Click here
21. REMOVE IGNITION COIL ASSEMBLY
Click here
22. REMOVE VACUUM PUMP ASSEMBLY
Click here
23. REMOVE NO. 1 VACUUM PUMP BRACKET
Click here
24. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Click here
25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Click here
26. REMOVE CYLINDER HEAD COVER GASKET
Click here
27. SET NO. 1 CYLINDER TO TDC/COMPRESSION
Click here
28. REMOVE CRANKSHAFT PULLEY
Click here
29. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Click here
30. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Click here
31. REMOVE TIMING CHAIN COVER OIL SEAL
Click here
32. REMOVE CHAIN TENSIONER SLIPPER
Click here
33. REMOVE NO. 1 CHAIN VIBRATION DAMPER
Click here
34. REMOVE CHAIN SUB-ASSEMBLY
Click here
35. REMOVE CRANKSHAFT TIMING SPROCKET
Click here
36. REMOVE NO. 2 CHAIN SUB-ASSEMBLY
Click here
37. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Click here
38. REMOVE OIL PUMP ASSEMBLY
(a) Remove the 3 bolts and oil pump assembly from the stiffening crankcase assembly.
|
|
|