Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001G45K |
Model Year Start: 2020 |
Model: Corolla |
Prod Date Range: [01/2019 - 03/2019] |
Title: 2ZR-FAE (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION; 2020 MY Corolla [01/2019 - 03/2019] |
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
HINT:
Perform "Inspection After Repair" after replacing the engine assembly.
Click here
PROCEDURE
1. INSTALL ENGINE HANGERS
Click here
2. REMOVE ENGINE FROM ENGINE STAND
(a) Remove the engine assembly from the engine stand.
3. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
Click here
4. INSTALL GENERATOR ASSEMBLY
Click here
5. INSTALL V-RIBBED BELT
Click here
6. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
Click here
7. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
Click here
8. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
Click here
9. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
Click here
10. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)
Click here
11. INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY (for Manual Transaxle)
Click here
12. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
Click here
13. INSPECT CLUTCH PIPE LINE (for Manual Transaxle)
Click here
14. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
Click here
15. INSTALL BLEEDER CLUTCH RELEASE TUBE (for Manual Transaxle)
Click here
16. INSTALL ENGINE ASSEMBLY (for CVT)
Click here
17. INSTALL ENGINE ASSEMBLY (for Manual Transaxle)
Click here
18. INSTALL WATER BY-PASS HOSE ASSEMBLY (for CVT)
(a) Install the water by-pass hose assembly to the oil cooler and slide the 2 clips to secure it.
(b) Install the water by-pass hose assembly to the No. 3 water by-pass pipe and cylinder head sub-assembly and slide the 2 clips to secure it.
(c) Engage the clamp.
19. INSTALL ENGINE WIRE
(a) Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.
20. INSTALL FLYWHEEL HOUSING SIDE COVER
(a) Install the flywheel housing side cover to the cylinder block sub-assembly.
21. INSTALL STARTER ASSEMBLY
Click here
22. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
HINT:
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
(a) Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.
|
|
(b) Install the 2 bolts and nut in the order shown in the illustration.
Torque:
72 N·m {734 kgf·cm, 53 ft·lbf}
(c) Connect the air conditioner tube and accessory assembly to the engine mounting insulator sub-assembly RH with the bolt and nut.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
(d) Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle with the 2 bolts.
Torque:
10.5 N·m {107 kgf·cm, 8 ft·lbf}
23. INSTALL ENGINE MOUNTING INSULATOR LH
HINT:
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
(a) Temporarily install the engine mounting insulator LH to the vehicle.
|
|
*A
|
for CVT
|
*B
|
for Manual Transaxle
|
*a
|
Temporarily Tighten
|
|
|
(b) Install the 4 bolts and nut in the order shown in the illustration.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
24. REMOVE ENGINE HANGERS
Click here
25. INSTALL WIRE HARNESS CLAMP BRACKET
(a) Install the wire harness clamp bracket with the bolt.
Torque:
39 N·m {398 kgf·cm, 29 ft·lbf}
(b) Connect the air fuel ratio sensor connector.
(c) Engage the 4 clamps.
26. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
(a) Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
NOTICE:
-
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
-
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
-
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
(b) Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
CAUTION:
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
NOTICE:
-
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
-
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
(c) Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.
Torque:
141 N·m {1438 kgf·cm, 104 ft·lbf}
(d) Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.
Torque:
44 N·m {449 kgf·cm, 32 ft·lbf}
NOTICE:
While holding the nut in place, tighten the bolt.
(e) Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.
Torque:
Bolt :
72 N·m {734 kgf·cm, 53 ft·lbf}
Nut :
41 N·m {418 kgf·cm, 30 ft·lbf}
27. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
Click here
28. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
29. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for CVT)
Click here
30. INSTALL FLYWHEEL HOUSING UNDER COVER
(a) Install the flywheel housing under cover to the stiffening crankcase assembly.
31. CONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)
(a) Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.
(b) Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.
Torque:
Specified tightening torque :
15.2 N·m {155 kgf·cm, 11 ft·lbf}
HINT:
-
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
-
When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
|
|
*a
|
10 mm Union Nut Wrench
|
*b
|
Torque Wrench Fulcrum Length
|
|
|
32. INSTALL DRIVE SHAFT ASSEMBLY
Click here
33. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)
Click here
34. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
Click here
35. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
Click here
36. INSTALL COLUMN HOLE COVER SILENCER SHEET
Click here
37. CONNECT SUCTION HOSE SUB-ASSEMBLY
Click here
38. CONNECT DISCHARGE HOSE SUB-ASSEMBLY
Click here
39. CONNECT FUEL TUBE SUB-ASSEMBLY
(a) Connect the fuel tube sub-assembly to the fuel pipe.
Click here
(b) Engage the claw and install the No. 1 fuel pipe clamp.
40. CONNECT INLET HEATER WATER HOSE
(a) Connect the inlet heater water hose to the No. 1 water by-pass pipe and slide the clip to secure it.
41. CONNECT OUTLET HEATER WATER HOSE
(a) Connect the outlet heater water hose to the No. 3 water by-pass hose and slide the clip to secure it.
(b) Engage the clamp.
42. CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE
Click here
43. CONNECT FUEL VAPOR FEED HOSE
(a) Connect the fuel vapor feed hose to the purge valve (purge VSV) and slide the clip to secure it.
44. CONNECT FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE (for CVT)
Click here
45. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
(a) Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).
NOTICE:
Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.
|
|
(b) Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).
46. CONNECT NO. 2 RADIATOR HOSE
(a) Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.
47. CONNECT NO. 1 RADIATOR HOSE
(a) Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the clip to secure it.
48. INSTALL BATTERY CLAMP SUB-ASSEMBLY
(a) Install the battery clamp sub-assembly to the vehicle with the 3 bolts.
Torque:
15.4 N·m {157 kgf·cm, 11 ft·lbf}
(b) Engage the clamp to connect the engine wire to the battery clamp sub-assembly.
49. CONNECT WIRE HARNESS
(a) Connect the engine wire to the positive (+) battery terminal with the 3 nuts.
Torque:
7.6 N·m {77 kgf·cm, 67 in·lbf}
(b) Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.
Torque:
7.0 N·m {71 kgf·cm, 62 in·lbf}
(c) Connect the engine wire to the vehicle with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
|
|
50. INSTALL ECM
Click here
51. INSTALL BATTERY
Click here
52. BLEED CLUTCH LINE (for Manual Transaxle)
Click here
53. ADD ENGINE OIL
Click here
54. ADD ENGINE COOLANT
Click here
55. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
Click here
56. ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
Click here
57. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
-
for HFO-1234yf(R1234yf):
Click here
-
for HFC-134a(R134a):
Click here
58. WARM UP COMPRESSOR
-
for HFO-1234yf(R1234yf):
Click here
-
for HFC-134a(R134a):
Click here
59. INSPECT TRANSAXLE OIL (for Manual Transaxle)
Click here
60. ADJUST SHIFT LEVER POSITION (for Manual Transaxle)
Click here
61. INSPECT SHIFT LEVER POSITION (for CVT)
Click here
62. ADJUST SHIFT LEVER POSITION (for CVT)
Click here
63. INSPECT FOR ENGINE OIL LEAK
Click here
64. INSPECT FOR COOLANT LEAK
Click here
65. INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)
66. INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)
67. INSPECT FOR REFRIGERANT LEAK
-
for HFO-1234yf(R1234yf):
Click here
-
for HFC-134a(R134a):
Click here
68. INSPECT FOR FUEL LEAK
Click here
69. INSPECT FOR EXHAUST GAS LEAK
Click here
70. CHECK ENGINE OIL LEVEL
Click here
71. INSPECT RADIATOR RESERVE TANK ENGINE COOLANT LEVEL
Click here
72. INSTALL REAR ENGINE UNDER COVER LH
(a) Type A:
(1) Install the rear engine under cover LH to the vehicle with the 4 clips.
(2) Install the screw.
(b) Type B:
(1) Install the rear engine under cover LH to the vehicle with the 5 clips.
(2) Install the screw.
73. INSTALL REAR ENGINE UNDER COVER RH
(a) Type A:
(1) Install the rear engine under cover RH to the vehicle with the 4 clips.
(2) Install the screw.
(b) Type B:
(1) Install the rear engine under cover RH to the vehicle with the 5 clips.
(2) Install the screw.
74. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
(a) Install the No. 1 engine under cover assembly to the vehicle with the 10 clips.
(b) Install the 4 bolts.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
75. INSTALL FRONT WHEELS
Click here
76. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
77. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here
78. PERFORM INITIALIZATION
Click here
79. INSPECT IGNITION TIMING
Click here
80. INSPECT ENGINE IDLE SPEED
Click here
81. INSPECT CO/HC
Click here
82. CHECK SPEED SENSOR SIGNAL
Click here
|