Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001D2LR |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 09/2022] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): C050014; Left Front Wheel Speed Sensor Circuit Short to Ground or Open; 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022] |
DTC
|
C050014
|
Left Front Wheel Speed Sensor Circuit Short to Ground or Open
|
DESCRIPTION
Refer to DTC C050012
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
C050014
|
Left Front Wheel Speed Sensor Circuit Short to Ground or Open
|
A short or open circuit is detected in the speed sensor signal circuit for 0.12 seconds or more.
|
-
Front speed sensor LH
-
Wire harness or connector
-
Skid control ECU (brake actuator assembly)
|
DTC Detection Conditions: C050014
|
Vehicle Condition
|
Pattern 1
|
Pattern 2
|
Diagnosis Condition
|
-
|
-
|
-
|
Malfunction Status
|
An open circuit is detected in the speed sensor signal circuit.
|
○
|
-
|
A short circuit is detected in the speed sensor signal circuit.
|
-
|
○
|
Detection Time
|
0.12 seconds or more.
|
0.12 seconds or more.
|
Number of Trips
|
1 trip
|
1 trip
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
WIRING DIAGRAM
Refer to DTC C050012.
Click here
CAUTION / NOTICE / HINT
NOTICE:
-
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
Click here
-
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
PROCEDURE
1.
|
CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
|
|
*a
|
Front view of wire harness connector
(to Front Speed Sensor LH)
|
|
|
(b) Disconnect the A13 front speed sensor LH connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Turn the engine switch on (IG).
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
A13-1 (FL+) - A13-2 (FL-)
|
Engine switch on (IG)
|
11 to 14 V
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the A13 front speed sensor LH connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A13-2 (FL-) or A51-7 (FL-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
3.
|
CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the A13 front speed sensor LH connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A13-2 (FL-) - A51-7 (FL-)
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|