SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001D1HT
Model Year Start: 2019	Model: GR Corolla	Prod Date Range: [06/2018 - 01/2019]
Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision system
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock	Power Door Lock Control System

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.
Be sure to read Precaution thoroughly before servicing.
Click here

NOTICE:

After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

3. REMOVE FRONT DOOR SCUFF PLATE

Click here

4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the front door opening trim weatherstrip.

5. REMOVE REAR DOOR SCUFF PLATE

Click here

6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the rear door opening trim weatherstrip.

7. REMOVE LAP BELT OUTER ANCHOR COVER

(a) Disengage the 3 claws to remove the lap belt outer anchor cover.

8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.

9. REMOVE CENTER PILLAR LOWER GARNISH

Click here

10. REMOVE CENTER PILLAR UPPER GARNISH

Click here

11. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

(b) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.

*a	Protective Tape
*b	Locking Button
*c	Release

(d) Disengage the 2 guides to remove the front seat outer belt assembly.

12. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.