Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001D1GR |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 06/2020] |
Title: INTERIOR PANELS / TRIM: ROOF HEADLINING (for Hatchback): REMOVAL; 2019 - 2021 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 06/2020] |
REMOVAL
PROCEDURE
1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Remove the package tray trim panel assembly.
2. REMOVE REAR FLOOR MAT ASSEMBLY (w/o Spare Tire)
(a) Remove the rear floor mat assembly.
3. REMOVE REAR DECK TRIM COVER (w/o Spare Tire)
(b) Disengage the 2 guides to remove the 2 luggage hold belt striker assemblies.
(c) Disengage the 4 claws, 4 clips and 4 guides to remove the rear deck trim cover.
|
|
4. REMOVE DECK BOARD ASSEMBLY (w/ Spare Tire)
(a) Remove the deck board assembly.
5. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)
(a) Remove the clip and deck floor box LH.
|
|
6. REMOVE DECK FLOOR BOX RH (w/ Spare Tire)
(a) Remove the clip and deck floor box RH.
|
|
7. REMOVE REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
(a) Disengage the 7 clips to remove the rear No. 1 floor board.
|
|
8. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)
(b) Disengage the 2 clips to remove the front deck floor box.
9. REMOVE REAR DECK TRIM COVER (w/ Spare Tire)
(b) Disengage the 2 guides to remove the 2 luggage hold belt striker assemblies.
(c) Disengage the 4 claws, 4 clips and 4 guides to remove the rear deck trim cover.
|
|
10. REMOVE REAR SEAT ASSEMBLY
Click here
11. REMOVE FRONT DOOR SCUFF PLATE LH
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
HINT:
Use the same procedure for the front side and rear side.
(b) Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.
|
Remove in this Direction
|
12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
(a) Remove the clip.
|
Remove in this Direction
|
(b) Disengage the 2 clips to remove the cowl side trim sub-assembly LH as shown in the illustration.
13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
14. REMOVE FRONT PILLAR GARNISH LH
(a) Apply protective tape around the front pillar garnish LH as shown in the illustration.
|
Protective Tape
|
(b) Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the front pillar garnish clip.
HINT:
Let the front pillar garnish LH hang from the front pillar garnish clip.
|
Remove in this Direction
|
(c) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
HINT:
When the front pillar garnish clip cannot be disengaged easily:
(d) Disengage the front pillar garnish LH from the base of the front pillar garnish clip as shown in the illustration.
|
Remove in this Direction
|
HINT:
Let the front pillar garnish LH hang from the front pillar garnish clip.
(e) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
HINT:
When the front pillar garnish clip cannot be disengaged easily:
(f) w/o Front No. 3 Speaker:
(1) Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
|
Remove in this Direction
|
(g) w/ Front No. 3 Speaker:
(1) Disengage the 2 guides as shown in the illustration.
(2) Disconnect the connector to remove the front pillar garnish LH.
(h) Remove the 2 front pillar garnish clips from the front pillar garnish LH.
(i) Protect the curtain shield airbag assembly LH.
(1) Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.
NOTICE:
Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.
|
|
*1
|
Curtain Shield Airbag Assembly LH
|
*a
|
Protective Cover
|
*b
|
Adhesive Tape
|
|
|
15. REMOVE REAR DOOR SCUFF PLATE LH
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
(b) Disengage the 6 claws and 2 guides to remove the rear door scuff plate LH as shown in the illustration.
|
Remove in this Direction
|
16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
17. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
Click here
18. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
19. REMOVE CENTER PILLAR LOWER GARNISH LH
(a) Pull the center pillar lower garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).
*a
|
Claw (A)
|
*b
|
Claw (B)
|
|
Place Hand Here
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(b) Pull the center pillar lower garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).
(c) Disengage the 3 clips to remove the center pillar lower garnish LH as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
20. REMOVE CENTER PILLAR UPPER GARNISH LH
(a) Using a clip remover, remove the 2 clips.
|
|
(b) Pull the center pillar upper garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the guide (A).
*a
|
Guide (A)
|
*b
|
Guide (B)
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(c) Pull the center pillar upper garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the clip and 2 guides (B).
(d) Pass the anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
21. REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
22. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
24. REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
25. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
27. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
29. REMOVE CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
30. REMOVE CENTER PILLAR UPPER GARNISH RH
HINT:
Use the same procedure as for the LH side.
31. REMOVE REAR SEAT SIDE GARNISH LH
(a) Disengage the clip, 2 claws and 2 guides.
|
|
(b) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration and remove the rear seat side garnish LH.
*1
|
Rear Seatback Hinge Sub-assembly LH
|
|
Remove in this Direction
|
32. REMOVE DECK TRIM SIDE LOWER BOARD LH (w/ Spare Tire)
(a) Disengage the 4 claws to remove the deck trim side lower board LH.
|
|
33. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
(b) Disengage the guide to remove the luggage hold belt striker assembly.
(c) Using a clip remover, remove the 2 clips.
*1
|
Deck Trim Side Panel Assembly LH
|
*2
|
Roof Side Inner Garnish LH
|
*a
|
Moulding Remover
|
-
|
-
|
|
Remove in this Direction
|
-
|
-
|
(d) Using a moulding remover, disengage the 3 claws as shown in the illustration.
NOTICE:
Do not forcefully pull the deck trim side panel assembly LH as it may become damaged.
(e) Disengage the 2 clips to remove the deck trim side panel assembly LH.
34. DISCONNECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH
Click here
35. REMOVE ROOF SIDE INNER GARNISH LH
(a) Disengage the 9 clips as shown in the illustration.
|
Remove in this Direction
|
-
|
-
|
(b) Pass the anchor of the rear 3 point type seat outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.
36. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
37. REMOVE DECK TRIM SIDE LOWER BOARD RH (w/ Spare Tire)
HINT:
Use the same procedure as for the LH side.
38. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
39. DISCONNECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
40. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
41. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
42. REMOVE MAP LIGHT ASSEMBLY
Click here
43. REMOVE NO. 1 ROOM LIGHT ASSEMBLY
Click here
44. REMOVE VANITY LIGHT ASSEMBLY
Click here
45. REMOVE NO. 2 FORWARD RECOGNITION COVER
Click here
46. REMOVE NO. 1 FORWARD RECOGNITION COVER
Click here
47. REMOVE ASSIST GRIP SUB-ASSEMBLY
HINT:
Use the same procedure for all assist grip sub-assemblies.
(a) Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
SST: 09813-00010
NOTICE:
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
|
|
(b) Pull SST as shown in the illustration to disengage the claw.
NOTICE:
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
*a
|
30 to 45°
|
|
Pull in this Direction
|
HINT:
-
Use the same procedure for the claw on the other side of the assist grip cover LH.
-
Use the same procedure for the LH side and RH side.
(c) Remove the assist grip cover LH.
HINT:
Use the same procedure for the LH side and RH side.
(d) Disengage the 2 clips as shown in the illustration to remove the assist grip sub-assembly.
|
Remove in this Direction
|
(e) Remove the 2 clips from the vehicle body.
48. REMOVE REAR ASSIST GRIP ASSEMBLY LH
HINT:
Use the same procedure as for the assist grip sub-assembly.
49. REMOVE REAR ASSIST GRIP ASSEMBLY RH
HINT:
Use the same procedure as for the assist grip sub-assembly.
50. REMOVE VISOR BRACKET COVER LH
(a) Disengage the 4 claws and remove the visor bracket cover LH.
|
|
51. REMOVE VISOR ASSEMBLY LH
(b) Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder.
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(c) Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
52. REMOVE VISOR BRACKET COVER RH
HINT:
Use the same procedure as for the LH side.
53. REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
54. REMOVE ROOF HEADLINING ASSEMBLY
(a) for Windshield Glass Side:
(1) Disconnect the 2 connectors.
(b) for Front Pillar LH Side:
(1) Remove the protective cover.
(2) Using a clip remover, disengage the 4 clamps.
|
|
(3) Disconnect the 2 connectors.
(4) Install the protective cover.
(c) for Front Pillar RH Side:
(1) Remove the protective cover.
(2) Using a clip remover, disengage the 3 clamps.
|
|
(3) Disconnect each connector.
(4) Install the protective cover.
(d) for Rear Pillar RH Side:
(1) Disengage the clamp.
*a
|
Clamp
|
*b
|
Guide
|
*c
|
Connector Bracket
|
|
Bolt
|
|
Connector
|
(2) Remove the bolt.
(3) Disengage the guide to disconnect the connector bracket.
(4) Disconnect the 2 connectors.
(e) Turn the visor holder approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.
*a
|
45°
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
HINT:
Use the same procedure for the LH side and RH side.
(f) Disengage the 2 claws to remove the base of each visor holder.
*a
|
Base of Visor Holder
|
-
|
-
|
(g) Using a clip remover, remove the 3 clips.
(h) Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
NOTICE:
Do not damage the roof headlining assembly or vehicle interior.
|
Remove in this Direction
|
|