Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001D0YP
Model Year Start: 2019 Model: Corolla Hatchback Prod Date Range: [06/2018 - 11/2022]
Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: Pattern Select Switch Sport Mode Circuit; 2019 - 2023 MY Corolla Corolla Hatchback [06/2018 - 11/2022]

Pattern Select Switch Sport Mode Circuit

DESCRIPTION

The TCM memory contains programs for normal and sport shift patterns.

By following the programs corresponding to signals from the SPORT switch (combination switch assembly), park/neutral position switch assembly and various other sensors, the TCM turns the shift solenoid valves on and off, and controls the transaxle gear ratio.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: PRECAUTION 2020 - 2022 MY Corolla Corolla Hatchback [01/2019 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: PRECAUTION 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: PRECAUTION

PROCEDURE

1.

READ VALUE USING TECHSTREAM (POWER MODE SW)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Data List.

(e) According to the display on the Techstream, read the Data List.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Power Mode SW

SPORT switch (combination switch assembly) status

OFF or ON

  • ON: SPORT switch (combination switch assembly) being pushed
  • OFF: SPORT switch (combination switch assembly) not being pushed

-

Powertrain > Engine > Data List

Tester Display

Power Mode SW

Result

Proceed to

Data List value is normal

A

Data List value is not normal

B

B

GO TO STEP 3

A

2.

REPLACE ECM

(a) Replace the ECM.

Click here 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; M20A-FKS (ENGINE CONTROL): ECM: COMPONENTS 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (ENGINE CONTROL): ECM: COMPONENTS

NEXT

PERFORM INITIALIZATION 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION

3.

INSPECT COMBINATION SWITCH ASSEMBLY (SPORT SWITCH)

(a) Remove the combination switch assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; K120 / K121 (CVT): PATTERN SELECT SWITCH: REMOVAL

*a

Component without harness connected

(Combination Switch Assembly (SPORT Switch))

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (MSW1) - 5 (E)

SPORT switch (combination switch assembly) being pushed

Below 50 Ω

6 (MSW1) - 5 (E)

SPORT switch (combination switch assembly) not being pushed

10 kΩ or higher

(c) Install the combination switch assembly.

Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; K120 / K121 (CVT): PATTERN SELECT SWITCH: INSTALLATION

NG

REPLACE COMBINATION SWITCH ASSEMBLY

OK

4.

CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)

(a) Disconnect the I61 combination switch assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I61-5 (E) - Body ground

Always

Below 1 Ω

(c) Connect the I61 combination switch assembly connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)

OK

5.

CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)

(a) Disconnect the A47 ECM connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A47-31 (PWMS) - Body ground

SPORT switch (combination switch assembly) being pushed

Below 50 Ω

A47-31 (PWMS) - Body ground

SPORT switch (combination switch assembly) not being pushed

10 kΩ or higher

(c) Connect the A47 ECM connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)

OK

6.

REPLACE ECM

(a) Replace the ECM.

Click here 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; M20A-FKS (ENGINE CONTROL): ECM: COMPONENTS 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (ENGINE CONTROL): ECM: COMPONENTS

NEXT

PERFORM INITIALIZATION 2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION