- The transmission revolution sensor (NOUT) signal is 1200 rpm or more
- TCM commands the C1 clutch to be released
- TCM commands the C2 clutch to be engaged
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001D0XY |
| Model Year Start: 2019 | Model: Corolla Hatchback | Prod Date Range: [06/2018 - ] |
| Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: P170300; AT Solenoid Output Malfunction; 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 - ] | ||
|
DTC |
P170300 |
AT Solenoid Output Malfunction |
DESCRIPTION
The TCM controls the shift solenoid valves SL1, SL2 and SLG to change the shift mode from gear mode to belt mode and vice versa.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P170300 |
AT Solenoid Output Malfunction |
Any of the following conditions are met for 1 second or more (2-trip detection logic):
|
|
Comes on |
DTC stored |
SAE Code: P1703 |
DTC Detection Condition Patterns:
|
Vehicle Condition |
|||
|---|---|---|---|
|
Pattern 1 |
Pattern 2 |
||
|
Diagnostic Condition |
2 seconds or more have elapsed since the following conditions are met |
○ |
- |
|
The transmission revolution sensor (NOUT) signal is 2050 rpm or more |
- |
○ |
|
|
Malfunction Condition |
C1 clutch is engaged, C2 clutch is released and S1 synchronizer is engaged |
○ |
○ |
|
Duration |
1 second or more |
1 second or more |
|
|
Detection Logic |
2-trip detection logic |
2-trip detection logic |
|
HINT:
This DTC is stored when any of the above detection patterns is met.
MONITOR DESCRIPTION
The TCM monitors the changes in the shift state from belt mode to gear mode for abnormalities.
If the vehicle is being driven in gear mode when in the belt mode vehicle speed range, the TCM detects a malfunction, illuminates the MIL and stores a DTC.
MONITOR STRATEGY
|
Related DTCs |
P1703: Incorrect shift solenoid performance/Functional check |
|
Required sensors/Components |
Transmission revolution sensor (NOUT) Shift solenoid valve SL1 Shift solenoid valve SL2 Shift solenoid valve SLG |
|
Frequency of operation |
Continuous |
|
Duration |
1 sec. |
|
MIL operation |
2 driving cycles |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
Condition (A)
|
Output speed |
1200 rpm or more |
|
Time after following condition is met |
2 sec. or more |
|
- TCM indicate |
Belt mode |
Condition (B)
|
Output speed |
2050 rpm or more |
TYPICAL MALFUNCTION THRESHOLDS
Condition (A) and (B)
|
Shift solenoid valve SL1 |
ON |
|
Shift solenoid valve SL2 |
OFF |
|
Shift solenoid valve SLG |
ON |
CONFIRMATION DRIVING PATTERN
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
-
When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
![2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Start the engine.
-
Perform the D Position Shift Test inspection in Road Test. [*1]
Click here
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P170300.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to DTC P074512, P077512 and P08C312.
for DTC P074512: Click here
for DTC P077512: Click here
for DTC P08C312: Click here
CAUTION / NOTICE / HINT
NOTICE:
-
Perform the universal trip to clear permanent DTCs.
Click here
-
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click here
-
Check that no DTCs are stored after performing initialization.
Click here
PROCEDURE
|
1. |
CHECK DTC OUTPUT (IN ADDITION TO DTC P170300) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Trouble Codes.
Powertrain > Transmission > Trouble Codes
(e) Read the DTCs using the Techstream.
HINT:
If any DTCs other than P170300 are output, perform troubleshooting for those DTCs first.
|
Result |
Proceed to |
|---|---|
|
Only DTC P170300 is output |
A |
|
DTC P170300 and other DTCs are output |
B |
| B |
|
GO TO DTC CHART
|
|
|
2. |
INSPECT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2, SLG) |
|
(a) Disconnect the C61 transmission wire connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (SL1+) - 7 (SL1-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
3 (SL2+) - 8 (SL2-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
1 (SLG+) - 6 (SLG-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
2 (SL1+) or 7 (SL1-) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
3 (SL2+) or 8 (SL2-) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
1 (SLG+) or 6 (SLG-) - Body ground and other terminals |
Always |
10 kΩ or higher |
(c) Connect the C61 transmission wire connector.
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) |
(a) Disconnect the C80 TCM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C80-38 (SL1+) - C80-37 (SL1-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
C80-19 (SL2+) - C80-20 (SL2-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
C80-21 (SLG+) - C80-22 (SLG-) |
20°C (68°F) |
5.0 to 5.6 Ω |
|
C80-38 (SL1+) or C80-37 (SL1-) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
C80-19 (SL2+) or C80-20 (SL2-) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
C80-21 (SLG+) or C80-22 (SLG-) - Body ground and other terminals |
Always |
10 kΩ or higher |
(c) Connect the C80 TCM connector.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM) |
|
|
4. |
REPLACE TCM |
(a) Replace the TCM.
Click here
| NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here
for Initialization: Click here
|
|
5. |
INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1, SL2 AND SLG) |
(a) Disconnect the transmission wire connector from the shift solenoid valves SL1, SL2 and SLG.
Click here
|
*1 |
Transmission Valve Body Assembly |
*2 |
Shift Solenoid Valve SLG |
|
*3 |
Shift Solenoid Valve SL1 |
*4 |
Shift Solenoid Valve SL2 |
|
*a |
Component without harness connected (Shift Solenoid Valve SL1, SL2 and SLG) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Shift solenoid valve SL1 connector terminal 1 - terminal 2 |
20°C (68°F) |
5.0 to 5.6 Ω |
|
Shift solenoid valve SL2 connector terminal 1 - terminal 2 |
20°C (68°F) |
5.0 to 5.6 Ω |
|
Shift solenoid valve SLG connector terminal 1 - terminal 2 |
20°C (68°F) |
5.0 to 5.6 Ω |
| OK |
|
REPLACE TRANSMISSION WIRE
|
|
|
6. |
REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY |
(a) Replace the continuously variable transaxle assembly.
Click here
| NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here
for Initialization: Click here
|
|
|