Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001D0PU |
Model Year Start: 2019 |
Model: Corolla Hatchback |
Prod Date Range: [06/2018 - 01/2019] |
Title: M20A-FKS (FUEL): FUEL INJECTOR (for Port Injection): REMOVAL; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision system
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
-
Replacement of port fuel injector assembly
-
Replacement of No. 2 fuel pressure sensor.
-
Replacement of EGR valve assembly
-
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
CAUTION:
-
Never perform work on fuel system components near any possible ignition sources.
-
Vaporized fuel could ignite, resulting in a serious accident.
-
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
-
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
NOTICE:
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
PROCEDURE
1. REMOVE NO. 2 FUEL PRESSURE SENSOR
Click here
2. DISCONNECT FUEL TUBE SUB-ASSEMBLY
(a) Remove the fuel pipe clamp from the fuel tube connector.
|
|
(b) Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.
Click here
|
|
3. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
(a) Disconnect the No. 5 engine wire connector.
|
|
(b) Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.
NOTICE:
-
If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
-
Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.
4. REMOVE FUEL DELIVERY SPACER
(a) Remove the 2 fuel delivery pipe spacers from the cylinder head sub-assembly.
|
|
5. REMOVE INJECTOR VIBRATION INSULATOR
(a) Remove the 4 injector vibration insulators from the cylinder head sub-assembly.
|
|
6. REMOVE NO. 5 ENGINE WIRE
(a) Disconnect the 4 port fuel injector assembly connectors.
|
|
(b) Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.
7. REMOVE PORT FUEL INJECTOR ASSEMBLY
(a) Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.
|
|
(b) Remove the O-ring from each port fuel injector assembly.
|
|
(c) Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.
NOTICE:
Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.
|
|
|