Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000001D0MZ |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 04/2020] |
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM (for Gasoline Model (w/o Safe Exit Assist Function)): DIAGNOSIS SYSTEM; 2019 - 2020 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 04/2020] |
DIAGNOSIS SYSTEM
DESCRIPTION
(a) Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the Techstream to check for malfunctions and perform repairs.
CHECK DLC3
(a) Check the DLC3.
Click here
DIAGNOSIS FUNCTION
(a) The blind spot monitor system displays an error message on the multi-information display to inform the driver that the system is unavailable either temporarily or due to a malfunction.
ABNORMALITY HISTORY
HINT:
The abnormality history for a blind spot monitor sensor can be displayed or cleared.
(a) Check abnormality history
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the Techstream on.
(4) Turn the blind spot monitor system on.
(5) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History.
Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
|
BSM Master Abnormal History
|
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
|
BSM Slave Abnormal History
|
(6) Check the results displayed for the abnormality history check.
HINT:
-
If "Yes" is displayed, check the suspected area column for each item.
-
Abnormality history is stored only for the blind spot monitor sensor for which an abnormality has been detected.
-
If "No" is displayed, refer to Problem Symptoms Table.
Click here
Abnormality History Table
Tester Display
|
Item Explanation
|
Suspected Area
|
History of Module Blockage
|
History of blind spot monitor sensor detection problems due to snow, rain, etc. on the bumper
|
-
Check if a bumper compatible with the blind spot monitor (such as an original equipment bumper) is installed
-
Check if any foreign matter is attached to the bumper
-
Check if any foreign matter is present between the bumper and sensors
|
History of Low Voltage
|
History of low supply battery voltage from battery to the blind spot monitor sensor
|
Power Source Circuit
|
History of High Voltage
|
History of high supply battery voltage from battery to the blind spot monitor sensor
|
History of Low Temperature
|
History of low temperature for the blind spot monitor sensor
|
-
Check the outside temperature
-
Check if any foreign matter is attached to the blind spot monitor sensors and their surrounding areas
|
History of High Temperature
|
History of high temperature for the blind spot monitor sensor
|
(b) Clearing abnormality history
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the Techstream on.
(4) Turn the blind spot monitor system on.
(5) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History.
Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
|
BSM Master Abnormal History
|
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
|
BSM Slave Abnormal History
|
(6) Clear the abnormality history.
|