- Poor idle, etc.
- Engine start function, etc.
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001D0HZ |
| Model Year Start: 2019 | Model: Corolla Hatchback | Prod Date Range: [06/2018 - 01/2019] |
| Title: M20A-FKS (INTAKE / EXHAUST): INTAKE MANIFOLD: REMOVAL; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Gas leaks from exhaust system is repaired |
Inspection after repair |
|
|
NOTICE:
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. REMOVE RADIATOR SUPPORT OPENING COVER
Click here
2. REMOVE INLET NO. 1 AIR CLEANER
Click here
3. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
4. SEPARATE THROTTLE BODY WITH MOTOR ASSEMBLY
|
(a) Disconnect the throttle body with motor assembly connector. |
|
(b) Using an 8 mm socket wrench, remove the 3 bolts to separate the throttle body with motor assembly from the intake manifold.
5. REMOVE THROTTLE BODY GASKET
Click here
6. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
Click here
7. REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)
Click here
8. DISCONNECT ENGINE WIRE
|
(a) Disconnect the connector. |
|
(b) Remove the 2 bolts.
(c) Disengage the 2 wire harness clamps and disconnect the engine wire.
|
(d) Remove the bolt. |
|
(e) Disengage the wire harness clamp and disconnect the engine wire.
9. SEPARATE NO. 3 WATER BY-PASS PIPE
|
(a) Using an 8 mm socket wrench, remove the bolt and separate the No. 3 water by-pass pipe from the intake manifold. |
|
10. REMOVE INTAKE MANIFOLD STAY
|
(a) Using an 8 mm socket wrench, remove the bolt (A). |
|
(b) Remove the bolt (B).
(c) Disengage the guide to remove the intake manifold stay.
11. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
|
(a) Slide the clip and disconnect the No. 1 fuel vapor feed hose from the intake manifold. |
|
12. REMOVE INTAKE MANIFOLD
|
(a) w/o Stud Bolt: (1) Remove the 5 bolts and separate the intake manifold from the cylinder head sub-assembly. |
|
(b) w/ Stud Bolt:
(1) Remove the 3 bolts and 2 nuts.
|
(2) Using an E8 "TORX" socket wrench, remove the 2 stud bolts and separate the intake manifold from the cylinder head sub-assembly. |
|
|
(c) Disconnect the fuel pressure sensor connector. |
|
(d) Remove the intake manifold.
13. REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
|
(a) Remove the No. 1 intake manifold to head gasket from the intake manifold. |
|
14. REMOVE VACUUM HOSE
|
(a) Remove the vacuum hose from the intake manifold. |
|
|
|