| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001D0GM |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 09/2022] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): B1653; Driver Side Seat Position Sensor; 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022] | ||
|
DTC |
B1653 |
Driver Side Seat Position Sensor |
DESCRIPTION
The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.
DTC B1653 is stored when a malfunction is detected in the seat position airbag sensor circuit.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
Test Mode / Check Mode |
|---|---|---|---|---|---|
|
B1653 |
Driver Side Seat Position Sensor |
|
for Manual Seat:
for Power Seat:
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
for Manual Seat:
for Power Seat:
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK VEHICLE CONDITION |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for Manual Seat |
A |
|
for Power Seat |
B |
| B |
|
|
|
2. |
CHECK CONNECTION OF CONNECTORS |
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor.
OK:
The connectors are properly connected.
| NG |
|
CONNECT CONNECTORS PROPERLY |
|
|
3. |
CHECK CONNECTORS |
(a) Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG |
|
REPLACE FLOOR WIRE OR FRONT SEAT INNER BELT ASSEMBLY LH |
|
|
4. |
CHECK WIRE HARNESS |
|
(a) Connect the connectors to the front seat inner belt assembly LH and floor wire. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
z20-2 (VS) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
z20-1 (GND) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
z20-2 (VS) - z20-1 (GND) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
z20-2 (VS) - z20-1 (GND) |
Always |
1 MΩ or higher |
|
z20-2 (VS) - Body ground |
Always |
1 MΩ or higher |
|
z20-1 (GND) - Body ground |
Always |
1 MΩ or higher |
| NG |
|
|
|
5. |
CHECK DTC |
|
(a) Connect the connectors to the airbag sensor assembly and seat position airbag sensor. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1653 is not output.
HINT:
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
| OK |
|
|
|
6. |
CHECK SEAT POSITION AIRBAG SENSOR |
|
(a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Replace the seat position airbag sensor with a known good one.
Click here
HINT:
Perform the following inspection using known good parts from another vehicle if possible.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1653 is not output.
HINT:
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Restore the seat position airbag sensor that was installed for testing to its original location.
Click here
| OK |
|
REPLACE SEAT POSITION AIRBAG SENSOR
|
| NG |
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
|
7. |
CHECK FLOOR WIRE |
|
(a) Disconnect the floor wire connector from the front seat inner belt assembly LH. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
O23-3 (LSP-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - O23-3 (LSP-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - O23-3 (LSP-) |
Always |
1 MΩ or higher |
|
O23-4 (LSP+) - Body ground |
Always |
1 MΩ or higher |
|
O23-3 (LSP-) - Body ground |
Always |
1 MΩ or higher |
| OK |
|
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
|
| NG |
|
REPLACE FLOOR WIRE |
|
8. |
CHECK CONNECTION OF CONNECTORS |
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.
OK:
The connectors are properly connected.
| NG |
|
CONNECT CONNECTORS PROPERLY |
|
|
9. |
CHECK CONNECTORS |
(a) Disconnect the connectors from the airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG |
|
REPLACE FLOOR WIRE, FRONT SEAT NO. 2 WIRE LH OR FRONT SEAT INNER BELT ASSEMBLY LH |
|
|
10. |
CHECK WIRE HARNESS |
(a) Connect the floor wire and front seat No. 2 wire LH to the front seat inner belt assembly LH.
|
*1 |
Seat Position Airbag Sensor |
*2 |
Front Seat Inner Belt Assembly LH |
|
*3 |
Airbag Sensor Assembly |
*4 |
Front Seat No. 2 Wire LH |
|
*5 |
Floor Wire |
*6 |
Service Wire |
|
*a |
Front view of wire harness connector (to Airbag Sensor Assembly) |
*b |
Front view of wire harness connector (to Seat Position Airbag Sensor) |
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
q10-2 (VS) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
q10-1 (GND) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
q10-2 (VS) - q10-1 (GND) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
q10-2 (VS) - q10-1 (GND) |
Always |
1 MΩ or higher |
|
q10-2 (VS) - Body ground |
Always |
1 MΩ or higher |
|
q10-1 (GND) - Body ground |
Always |
1 MΩ or higher |
| NG |
|
|
|
11. |
CHECK DTC |
|
(a) Connect the connectors to the airbag sensor assembly and seat position airbag sensor. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(e) Turn the engine switch off.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1653 is not output.
HINT:
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
| OK |
|
|
|
12. |
CHECK SEAT POSITION AIRBAG SENSOR |
|
(a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Replace the seat position airbag sensor with a known good one.
Click here
HINT:
Perform the following inspection using known good parts from another vehicle if possible.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
OK:
DTC B1653 is not output.
HINT:
Codes other than DTC B1653 may be output at this time, but they are not related to this check.
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Restore the seat position airbag sensor that was installed for testing to its original location.
Click here
| OK |
|
REPLACE SEAT POSITION AIRBAG SENSOR
|
| NG |
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
|
13. |
CHECK WIRE HARNESS |
(a) Disconnect the front seat No. 2 wire LH connector from the front seat inner belt assembly LH.
|
*1 |
Seat Position Airbag Sensor |
*2 |
Front Seat Inner Belt Assembly LH |
|
*3 |
Airbag Sensor Assembly |
*4 |
Front Seat No. 2 Wire LH |
|
*5 |
Floor Wire |
*6 |
Service Wire |
|
*a |
Front view of wire harness connector (to Airbag Sensor Assembly) |
*b |
Front view of wire harness connector (to Front Seat No. 2 Wire LH) |
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
E-2 (LSP+) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
E-1 (LSP-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
E-2 (LSP+) - E-1 (LSP-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
E-2 (LSP+) - E-1 (LSP-) |
Always |
1 MΩ or higher |
|
E-2 (LSP+) - Body ground |
Always |
1 MΩ or higher |
|
E-1 (LSP-) - Body ground |
Always |
1 MΩ or higher |
| OK |
|
REPLACE FRONT SEAT NO. 2 WIRE LH |
|
|
14. |
CHECK FLOOR WIRE |
(a) Disconnect the floor wire connector from the front seat inner belt assembly LH.
|
*1 |
Seat Position Airbag Sensor |
*2 |
Front Seat Inner Belt Assembly LH |
|
*3 |
Airbag Sensor Assembly |
*4 |
Front Seat No. 2 Wire LH |
|
*5 |
Floor Wire |
*6 |
Service Wire |
|
*a |
Front view of wire harness connector (to Airbag Sensor Assembly) |
*b |
Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - Body ground |
Engine switch on (IG) |
Below 1 V |
|
O23-3 (LSP-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - O23-3 (LSP-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O23-4 (LSP+) - O23-3 (LSP-) |
Always |
1 MΩ or higher |
|
O23-4 (LSP+) - Body ground |
Always |
1 MΩ or higher |
|
O23-3 (LSP-) - Body ground |
Always |
1 MΩ or higher |
| OK |
|
REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
|
| NG |
|
REPLACE FLOOR WIRE |
|
|