| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001D0CG |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: INSPECTION; 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ] | ||
INSPECTION
PROCEDURE
1. INSPECT SPIRAL CABLE SUB-ASSEMBLY
NOTICE:
- Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
- Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
(a) Visually check the spiral cable sub-assembly for defects.
(1) The defects are as follows:
- Scratches
- Small cracks
- Dents
- Chips
-
Cracks or other damage to the connector
OK:
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
(b) Check the spiral cable sub-assembly.
|
*A |
w/o Heated Steering Wheel System |
*B |
w/ Heated Steering Wheel System |
|
*a |
Component without harness connected (Spiral Cable Sub-assembly) |
*b |
Color: Light Green |
|
*c |
Color: Black |
- |
- |
|
Interlock |
- |
- |
NOTICE:
- When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
- As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
(1) Set the spiral cable sub-assembly to the center position.
Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
(2) Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
| *: w/ Heated Steering Wheel System | ||
|
I82-1 (SDN) - z6-4 (SDN) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z6-3 (ECC) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z3-12 (ECC) |
Always |
3 Ω or less |
|
I82-4 (EAU) - z3-10 (EAU) |
Always |
3 Ω or less |
|
I82-5 (AU2) - z3-9 (AU2) |
Always |
3 Ω or less |
|
I82-6 (DIST) - z3-8 (DIST) |
Always |
3 Ω or less |
|
I82-7 (HO) - A (HO) |
Always |
3 Ω or less |
|
I82-8 (SUP) - z6-2 (SUP) |
Always |
3 Ω or less |
|
I82-9 (IL-2) - z3-6 (IL-2) |
Always |
3 Ω or less |
|
I82-10 (+DP2) - z3-5 (+DP2) |
Always |
3 Ω or less |
|
I82-11 (+DP) - z3-4 (+DP) |
Always |
3 Ω or less |
|
I82-12 (AU1) - z3-3 (AU1) |
Always |
3 Ω or less |
|
I82-13 (CCS) - z3-2 (CCS) |
Always |
3 Ω or less |
|
I82-14 (IL+2) - z3-1 (IL+2) |
Always |
3 Ω or less |
|
I22-1 (D+) - z15-2 (D+) |
Always |
Below 1 Ω |
|
I22-2 (D-) - z15-1 (D-) |
Always |
Below 1 Ω |
|
I22-3 (D2-) - z16-1 (D2-) |
Always |
Below 1 Ω |
|
I22-4 (D2+) - z16-2 (D2+) |
Always |
Below 1 Ω |
|
I19-2 (EHT) - z4-1 (EHT)* |
Always |
Below 0.1 Ω |
|
I19-4 (BHT) - z4-4 (BHT)* |
Always |
Below 0.1 Ω |
(3) After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
| *: w/ Heated Steering Wheel System | ||
|
I82-1 (SDN) - z6-4 (SDN) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z6-3 (ECC) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z3-12 (ECC) |
Always |
3 Ω or less |
|
I82-4 (EAU) - z3-10 (EAU) |
Always |
3 Ω or less |
|
I82-5 (AU2) - z3-9 (AU2) |
Always |
3 Ω or less |
|
I82-6 (DIST) - z3-8 (DIST) |
Always |
3 Ω or less |
|
I82-7 (HO) - A (HO) |
Always |
3 Ω or less |
|
I82-8 (SUP) - z6-2 (SUP) |
Always |
3 Ω or less |
|
I82-9 (IL-2) - z3-6 (IL-2) |
Always |
3 Ω or less |
|
I82-10 (+DP2) - z3-5 (+DP2) |
Always |
3 Ω or less |
|
I82-11 (+DP) - z3-4 (+DP) |
Always |
3 Ω or less |
|
I82-12 (AU1) - z3-3 (AU1) |
Always |
3 Ω or less |
|
I82-13 (CCS) - z3-2 (CCS) |
Always |
3 Ω or less |
|
I82-14 (IL+2) - z3-1 (IL+2) |
Always |
3 Ω or less |
|
I22-1 (D+) - z15-2 (D+) |
Always |
Below 1 Ω |
|
I22-2 (D-) - z15-1 (D-) |
Always |
Below 1 Ω |
|
I22-3 (D2-) - z16-1 (D2-) |
Always |
Below 1 Ω |
|
I22-4 (D2+) - z16-2 (D2+) |
Always |
Below 1 Ω |
|
I19-2 (EHT) - z4-1 (EHT)* |
Always |
Below 0.1 Ω |
|
I19-4 (BHT) - z4-4 (BHT)* |
Always |
Below 0.1 Ω |
(4) After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
| *: w/ Heated Steering Wheel System | ||
|
I82-1 (SDN) - z6-4 (SDN) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z6-3 (ECC) |
Always |
3 Ω or less |
|
I82-2 (ECC) - z3-12 (ECC) |
Always |
3 Ω or less |
|
I82-4 (EAU) - z3-10 (EAU) |
Always |
3 Ω or less |
|
I82-5 (AU2) - z3-9 (AU2) |
Always |
3 Ω or less |
|
I82-6 (DIST) - z3-8 (DIST) |
Always |
3 Ω or less |
|
I82-7 (HO) - A (HO) |
Always |
3 Ω or less |
|
I82-8 (SUP) - z6-2 (SUP) |
Always |
3 Ω or less |
|
I82-9 (IL-2) - z3-6 (IL-2) |
Always |
3 Ω or less |
|
I82-10 (+DP2) - z3-5 (+DP2) |
Always |
3 Ω or less |
|
I82-11 (+DP) - z3-4 (+DP) |
Always |
3 Ω or less |
|
I82-12 (AU1) - z3-3 (AU1) |
Always |
3 Ω or less |
|
I82-13 (CCS) - z3-2 (CCS) |
Always |
3 Ω or less |
|
I82-14 (IL+2) - z3-1 (IL+2) |
Always |
3 Ω or less |
|
I22-1 (D+) - z15-2 (D+) |
Always |
Below 1 Ω |
|
I22-2 (D-) - z15-1 (D-) |
Always |
Below 1 Ω |
|
I22-3 (D2-) - z16-1 (D2-) |
Always |
Below 1 Ω |
|
I22-4 (D2+) - z16-2 (D2+) |
Always |
Below 1 Ω |
|
I19-2 (EHT) - z4-1 (EHT)* |
Always |
Below 0.1 Ω |
|
I19-4 (BHT) - z4-4 (BHT)* |
Always |
Below 0.1 Ω |
If the result is not as specified, replace the spiral cable sub-assembly.
|
|