Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001D0BN
Model Year Start: 2019 Model: Corolla Hatchback Prod Date Range: [06/2018 - 01/2019]
Title: STEERING COLUMN: STEERING WHEEL (except G16E-GTS): REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

NOTICE:

  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
  • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

PROCEDURE

1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

2. REMOVE HORN BUTTON ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: STEERING PAD (except G16E-GTS): REMOVAL

3. REMOVE STEERING WHEEL ASSEMBLY

(a) Disconnect each connector.

(b) Using a 10 mm hexagon socket wrench, remove the steering wheel assembly set bolt.

(c) Put matchmarks on the steering wheel assembly and steering main shaft.

*a

Matchmark

(d) Temporarily install the steering wheel assembly set bolt.

NOTICE:

Do not overtighten the steering wheel assembly set bolt.

(e) Using SST, separate the steering wheel assembly.

SST: 09950-50013

09951-05010

09952-05010

09953-05020

09954-05031

09957-04010

SST: 09950-60011

09951-00330

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

*a

Turn

*b

Hold

(f) Remove the steering wheel assembly set bolt and steering wheel assembly.

4. REMOVE STEERING PAD SWITCH ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; STEERING COLUMN: STEERING PAD SWITCH (except G16E-GTS): REMOVAL+

5. REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; K120 / K121 (CVT): SHIFT PADDLE SWITCH: REMOVAL+