STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001D0BL
Model Year Start: 2019	Model: GR Corolla	Prod Date Range: [06/2018 - 01/2019]
Title: STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]

INSTALLATION

PROCEDURE

1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

2. INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.

(a) Install the steering column assembly with the bolt and 2 nuts.

Torque:

36 N·m {367 kgf·cm, 27 ft·lbf}

NOTICE:

After the steering column assembly is installed, check the tilt operation.
If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.
Tighten the nuts and check the tilt operation again.

(b) Connect each connector and engage each wire harness clamp to the steering column assembly.

3. INSTALL STOP LIGHT SWITCH ASSEMBLY

Click here

4. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

*a	Matchmark
	Install in this direction

(b) Install the No. 2 steering intermediate shaft assembly to the steering column assembly.

Torque:

64 N·m {653 kgf·cm, 47 ft·lbf}

5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.

*a	Matchmark
	Connect in this direction

(b) Connect the No. 2 steering intermediate shaft assembly to the steering gear assembly.

Torque:

64 N·m {653 kgf·cm, 47 ft·lbf}

6. INSTALL COLUMN HOLE COVER SILENCER SHEET

(a) Engage the 2 claws to install the column hole cover silencer sheet.

(b) Engage the claw to close the column hole cover silencer sheet.

Close in this direction

7. INSTALL NO. 1 AIR DUCT

(a) Engage the 3 claws to install a new No. 1 air duct.

(b) Install the 2 bolts.

8. INSTALL FRONT CONSOLE UPPER PANEL GARNISH

Click here

9. INSTALL FRONT NO. 1 CONSOLE BOX INSERT

Click here

10. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

11. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).
Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

(a) Using pliers, expand the clamp.

Clamp

(b) While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

(d) Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

12. INSTALL UPPER STEERING COLUMN COVER

(a) Engage the 2 claws and 4 clips to connect the upper steering column cover.

(b) Engage the claw to install the upper steering column cover.

13. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

(a) Engage the 2 claws to install the lower steering column cover sub-assembly.

(b) Install the 3 screws.

14. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

15. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Click here

16. INSTALL STEERING WHEEL ASSEMBLY

Click here

17. CHECK STEERING WHEEL CENTER POINT

18. INSTALL HORN BUTTON ASSEMBLY

Click here

19. PERFORM CALIBRATION AND REGISTRATION

for Power assist system calibration: Click here

for Smart key system registration: Click here