Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001D0BK |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: STEERING COLUMN: STEERING COLUMN ASSEMBLY: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
Power steering ECU assembly
|
-
Perform torque sensor zero point calibration
-
Assist map writing
|
-
DTCs are output
-
Steering effort different between turning steering wheel left and right
-
EPS warning light illuminates
|
|
Electric power steering column sub-assembly
|
Perform torque sensor zero point calibration
|
Steering lock ECU (steering lock actuator or upper bracket assembly)
|
Code registration (Smart Key System (for Start Function))
|
-
Wireless Door Lock Control System
-
Smart Key System (for Entry Function)
-
Smart Key System (for Start Function)
-
Steering lock function
|
|
NOTICE:
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. PRECAUTION
Click here
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3. REMOVE HORN BUTTON ASSEMBLY
Click here
4. REMOVE STEERING WHEEL ASSEMBLY
Click here
5. REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY
NOTICE:
Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.
(a) Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
(b) Lock the tilt and telescopic lever.
|
Push Area
|
|
Push in this direction
|
(d) While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.
6. REMOVE UPPER STEERING COLUMN COVER
(a) Disengage the claw and separate the upper steering column cover.
|
Separate in this direction
|
(b) Disengage the 2 claws and 4 clips to remove the upper steering column cover.
|
|
7. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
NOTICE:
-
Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).
-
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).
-
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
(a) Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
(b) Using pliers, expand the clamp.
|
|
(c) While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
8. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here
9. REMOVE FRONT NO. 1 CONSOLE BOX INSERT
Click here
10. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here
11. REMOVE NO. 1 AIR DUCT
(a) Remove the 2 bolts.
*a
|
View A
|
|
Front
|
(b) Disengage the 3 claws to remove the No. 1 air duct.
NOTICE:
Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.
12. REMOVE COLUMN HOLE COVER SILENCER SHEET
(a) Disengage the claw and open the column hole cover silencer sheet.
|
Open in this direction
|
(b) Disengage the 2 claws to remove the column hole cover silencer sheet.
|
Place Hand Here
|
13. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
(a) Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.
*a
|
Matchmark
|
|
Separate in this direction
|
(b) Remove the bolt.
(c) Separate the No. 2 steering intermediate shaft assembly from the steering gear assembly.
14. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
(a) Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.
*a
|
Matchmark
|
|
Remove in this direction
|
(b) Remove the bolt.
(c) Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.
15. REMOVE STOP LIGHT SWITCH ASSEMBLY
Click here
16. REMOVE STEERING COLUMN ASSEMBLY
(a) Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
(b) Remove the bolt, 2 nuts and steering column assembly.
|
|
|