Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001D08W
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: POWER ASSIST SYSTEMS: POWER STEERING ECU: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power steering ECU with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

Power steering ECU with motor assembly
  • Perform torque sensor zero point calibration
  • Assist map writing
  • DTCs are output
  • Steering effort different between turning steering wheel left and right
  • EPS warning light illuminates

2019 - 2020 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2019]; POWER ASSIST SYSTEMS: POWER STEERING SYSTEM (for Gasoline Model (for Hatchback)): CALIBRATION

NOTICE:

  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. REMOVE STEERING COLUMN ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: REMOVAL

2. REMOVE STEERING LOCK ACTUATOR ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: DISASSEMBLY+

3. REMOVE POWER STEERING ECU WITH MOTOR ASSEMBLY

NOTICE:

  • Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.
  • If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.
  • Do not pull the wire harness of the electric power steering column sub-assembly.
  • Do not allow any moisture to come into contact with the power steering ECU with motor assembly.
  • Do not loosen any bolts not mentioned in the procedure.
  • Do not allow any foreign matter to contaminate the power steering ECU with motor assembly.

(a) Disconnect the connector.

(b) Remove the 2 bolts and power steering ECU with motor assembly from the electric power steering column sub-assembly.

4. REMOVE ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

(a) Remove the electric power steering motor shaft damper from the electric power steering column sub-assembly.