Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001CZRH
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 09/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): B1612,B1613; Front Airbag Sensor Lost Communication (RH); 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]

DTC

B1612

Front Airbag Sensor Lost Communication (RH)

DTC

B1613

Front Airbag Sensor Initialization Error (RH)

DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1612

Front Airbag Sensor Lost Communication (RH)
  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.
  • Front airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Instrument panel wire
  • Engine room main wire
  • Front airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

B1613

Front Airbag Sensor Initialization Error (RH)
  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.
  • Front airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Instrument panel wire
  • Engine room main wire
  • Front airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2019 - 04/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [04/2020 - 09/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the engine switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY
OK

2.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE INSTRUMENT PANEL WIRE OR ENGINE ROOM MAIN WIRE
OK

3.

CHECK FRONT AIRBAG SENSOR RH CIRCUIT

(a) Connect the connectors that link the engine room main wire and instrument panel wire.

*1

Front Airbag Sensor RH

*2

Airbag Sensor Assembly

*3

Engine Room Main Wire

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Front Airbag Sensor RH)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the engine switch on (IG).

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A40-2 (+SR) - Body ground

Engine switch on (IG)

Below 1 V

A40-1 (-SR) - Body ground

Engine switch on (IG)

Below 1 V

(e) Turn the engine switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A40-2 (+SR) - A40-1 (-SR)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A40-2 (+SR) - A40-1 (-SR)

Always

1 MΩ or higher

A40-2 (+SR) - Body ground

Always

1 MΩ or higher

A40-1 (-SR) - Body ground

Always

1 MΩ or higher
NG

GO TO STEP 5

OK

4.

CHECK FRONT AIRBAG SENSOR RH

(a) Connect the connector to the airbag sensor assembly.

*1

Front Airbag Sensor LH

*2

Airbag Sensor Assembly

(b) Interchange the front airbag sensor RH with LH and connect the connectors.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the engine switch on (IG), and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the engine switch off.

(g) Turn the engine switch on (IG), and wait for at least 60 seconds.

(h) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

Result

Proceed to

DTCs B1612, B1613, B1617 and B1618 are not output.

A

DTC B1617 or B1618 is output.

B

DTC B1612 or B1613 is output.

C

(i) Turn the engine switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Return the front airbag sensor RH and LH to their original positions and connect the connectors.

A

USE SIMULATION METHOD TO CHECK

B

REPLACE FRONT AIRBAG SENSOR RH 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT AIRBAG SENSOR: REMOVAL 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT AIRBAG SENSOR: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT AIRBAG SENSOR: REMOVAL

C

REPLACE AIRBAG SENSOR ASSEMBLY 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [01/2019 - 03/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [03/2019 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

5.

CHECK INSTRUMENT PANEL WIRE

(a) Disconnect the instrument panel wire connector from the engine room main wire.

*1

Front Airbag Sensor RH

*2

Airbag Sensor Assembly

*3

Engine Room Main Wire

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Engine Room Main Wire)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the engine switch on (IG).

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

AI4-4 (+SR) - Body ground

Engine switch on (IG)

Below 1 V

AI4-3 (-SR) - Body ground

Engine switch on (IG)

Below 1 V

(e) Turn the engine switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

AI4-4 (+SR) - AI4-3 (-SR)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

AI4-4 (+SR) - AI4-3 (-SR)

Always

1 MΩ or higher

AI4-4 (+SR) - Body ground

Always

1 MΩ or higher

AI4-3 (-SR) - Body ground

Always

1 MΩ or higher
OK

REPLACE ENGINE ROOM MAIN WIRE
NG

REPLACE INSTRUMENT PANEL WIRE