Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CZQ2 |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
-
Rear door glass sub-assembly
-
Rear door glass run
-
Rear door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
6. REMOVE REAR SPEAKER ASSEMBLY
Click here
7. REMOVE REAR DOOR FRAME GARNISH
Click here
8. REMOVE REAR DOOR NO. 1 VENT SEAL
Click here
9. REMOVE REAR DOOR PANEL PROTECTOR
Click here
10. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
11. REMOVE REAR DOOR GLASS RUN
Click here
12. DISCONNECT REAR DOOR WEATHERSTRIP
(a) Disconnect the rear door weatherstrip until the screw of the rear door window division bar sub-assembly is visible.
13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
15. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
(a) Disconnect the connector.
*a
|
Release Plate
|
|
Remove in this Direction
|
(b) Using a T30 "TORX" socket wrench, remove the 3 screws.
(c) Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
(d) When reusing the rear door lock with motor assembly:
(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.
|
|
16. REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
(a) Using a screwdriver, disengage the claw and open the cover as shown in the illustration.
|
|
(b) Remove the rear door lock open lever remote control cable as shown in the illustration.
|
Remove in this Direction
|
17. REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
(a) Using a screwdriver, disengage the 3 claws and open the cover as shown in the illustration.
|
|
(b) Remove the rear door inside lock/unlock knob locking cable as shown in the illustration.
|
Remove in this Direction
|
|