| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CZPZ |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: DOOR LOCK: FRONT DOOR LOCK: INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. INSTALL FRONT DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
(a) Install the front door inside lock/unlock knob locking cable as shown in the illustration.
|
Install in this Direction |
3. INSTALL FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
(a) Install the front door lock open lever remote control cable as shown in the illustration.
|
|
Install in this Direction |
4. INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY
(a) Engage the 2 claws as shown in the illustration.
|
|
Install in this Direction |
|
(b) Engage the 2 claws to install the front door lock cover sub-assembly as shown in the illustration. |
|
5. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
NOTICE:
- When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.
- Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
- Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.
(a) When reusing the front door lock with motor assembly:
(1) Install a new door lock wiring harness seal to the front door lock with motor assembly.
(b) Connect the front door lock open rod to the front door lock with motor assembly as shown in the illustration.
|
*1 |
Front Door Lock Open Rod |
|
|
Install in this Direction |
HINT:
Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.
(c) Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(d) Connect the connector.
6. INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; DOOR / HATCH: FRONT DOOR: REASSEMBLY+](/t3Portal/stylegraphics/info.gif)
7. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
Click here
8. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Click here
9. INSTALL FRONT DOOR GLASS RUN
Click here
10. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Click here
11. INSTALL FRONT DOOR SERVICE HOLE COVER
Click here
12. INSTALL FRONT DOOR VENT SEAL
Click here
13. INSTALL DOOR UPPER FRAME GARNISH
Click here
14. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
15. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
16. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
17. INSTALL FRONT DOOR ASSIST GRIP ASSEMBLY
Click here
18. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
Click here
19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here
20. INITIALIZE POWER WINDOW CONTROL SYSTEM
Click here
21. INSPECT POWER WINDOW OPERATION
Click here
|
|