Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CZPY |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
-
Front door glass sub-assembly
-
Front door glass run
-
Front door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Click here
4. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY
Click here
5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE DOOR UPPER FRAME GARNISH
Click here
9. REMOVE FRONT DOOR VENT SEAL
Click here
10. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
12. REMOVE FRONT DOOR GLASS RUN
Click here
13. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Click here
14. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
Click here
15. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Click here
16. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
(a) Disconnect the connector.
*1
|
Front Door Lock Open Rod
|
|
Remove in this Direction
|
(b) Using a T30 "TORX" socket wrench, remove the 3 screws.
(c) Slide the front door lock with motor assembly downward as shown in the illustration to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.
(d) When reusing the front door lock with motor assembly:
(1) Remove the door lock wiring harness seal from the front door lock with motor assembly.
|
|
17. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY
(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.
|
|
(b) Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.
|
Remove in this Direction
|
18. REMOVE FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
(a) Remove the front door lock open lever remote control cable as shown in the illustration.
|
Remove in this Direction
|
19. REMOVE FRONT DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
(a) Remove the front door inside lock/unlock knob locking cable as shown in the illustration.
|
Remove in this Direction
|
|